Kenwood KRF-V5010 Instruction Manual

Also see for KRF-V5010: Instruction manual Instruction manual Service manual Instruction manual

14PreparationsKRF-V7010/V6010/V5010 (En/T)34Adjust the volume levels for the speakers.Sit in your normal listening position and listen to the test tone. Adjust thevolume levels for the speakers until all speakers seem to be equallyloud.1 Use the MULTI CONTROL (TUNING/SKIP) to adjust the volumewhen the test tone is being output from the speaker channel tobe adjusted.The test tone issues from the speakers for 1.5 seconds at a timein the following sequence:Lch = Cch = Rch = Sch = Lch• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. ¢• If the speaker setting selects are changed, the speaker levelsettings are reset.2 Press the SETUP key.• The receiver enters the mode for inputting the distance to thespeakers.The channel indication blinks while the test tone is being output.Input the distance to the speakers.1 Measure the distance from the listening position to each of thespeakers.Jot down the distance to each of the speakers.Distance to front speakers: ____ feets (meters)Distance to surround speakers: ____ feets (meters)2 Use the MULTI CONTROL (TUNING/SKIP) to select the distanceto the front speakers.• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustablein 1 foot (0.3 m) increments.3 Press the SETUP key.4 Repeat steps 2 and 3 to input the distance for the surroundspeaker.5 Setup is complete when the input indication reappears.• The speakers you selected appear on the display. Confirm that allthe speakers have been correctly selected.• If you used the remote control (RC-R0507) to perform the settings,press the VIDEO key at this point to turn off the remote control’sown adjustment mode. In this case, the input source is notswitched.The speaker indicator to be adjusted blinks.Indication in feet Indication in metersDisplay when all speakers have been selected.Lch + dB1ASPSWL1)FT )M3.ASPRLCDSWRLPreparing for surround soundPreparing for playbackNormal playbackSome preparatory steps are needed before starting playback.Turning on the receiver1 Turn on the power to the related components.2 Turn on the power to this receiver by pressing POWER and ON/STANDBY keys.Selecting TAPE/MDSelect the source name corresponding to the component connectedto the MD/TAPE jacks. The initial factory setting is “TAPE”. To changethe source name associated with the MD/TAPE jacks to “MD,” followthe steps below:1 Use the INPUT SELECTOR knob to select “TAPE”.2 Hold down the AUTO key for more than two seconds.• The source indication changes to “MD”.• To return to the original indication, repeat the above procedure.• You also will need to change the name input to the remote control(RC-0507) to “MD”. RC3A ON : Sound from the speakers connected to the SPEAKERS Aterminals on the rear panel.B ON : Sound from the speakers connected to the SPEAKERS Bterminals on the rear panel.A+B ON : Sound from both the speakers connected to the SPEAK-ERS A and B terminals on the rear panel.A+B OFF : No sound from the speakers. Use this setting when listen-ing with headphones for stereo sound in all playbackmodes.• Activating a surround mode or selecting “DVD 6ch” as the inputsource causes speaker system A to be selected automatically.On the KRF-V5010, press the SPEAKERS key to switch the speak-ers on and off.Selecting VIDEO 2/MONITORDepending on the component connected to the VIDEO 2/MONITORjacks, select either the “VIDEO 2” setting or the “MONITOR” setting, asappropriate. 8The indicator for the speakersyou want to use should be lit.Selecting the speaker systemPress the SPEAKERS A or B key to select the speaker system tobe used.VIDEO 2/MONITORPOWERON/STANDBYSPEAKERS A/BSPEAKERS (KRF-V5010)AUTOINPUT SELECTORASPSWRLB SPSWRLSpeaker indicator lights.Models other than KRF-V5010 KRF-V5010Operations