Kenwood KRF-V6070D Instruction Manual

Also see for VR-707: Service manual Instruction manual Quick start guide

Kenwood KRF-V6070D Instruction Manual Manual pdf 29 page image

29 ENBasic remote control operations for other componentsRe-assigning device keysThe remote control can be set up to control a second TV or VCR, or anycombination of eight home entertainment components.For example, to control the operation of two different VCR using theremote control, the user need to re-assign the unused VID2 key tooperate the second VCR (VID1) as follows:1Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.2Press the numeric key to enter “9 - 9 - 2”.• The LED will blink twice.3Press the VID1 key once, then press the VID2 key once.•The user now can operate VID2 as a second VCR along with VID1.• Refer to the table in the previous page for the combination ofsource keys and the other components assignment. •4To re-assign other device keys, repeat steps 1through 3bysubstituting the key sequence from the chart below for themost popular components:To re-assign keySequence PerformTV as 2nd VID1 key Remote Setup -9 -9 -2 -VID1 - TVTV as 2nd VID2 key Remote Setup -9 -9 -2 -VID2 - TVTV as 2nd CD/DVD key Remote Setup -9 -9 -2 -CD/DVD - TVTV back to TV key Remote Setup -9 -9 -2 -TV - TVVID1 as 2nd TV key Remote Setup -9 -9 -2 -TV - VID1VID1 as 2nd VID2 key Remote Setup -9 -9 -2 -VID2 - VID1VID1 as 2nd CD/DVD key Remote Setup -9 -9 -2 -CD/DVD - VID1VID1 back to VID1 key Remote Setup -9 -9 -2 -VID1 - VID15To clear the re-assignment and reset the remote control to itsoriginal operation mode:1 Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.2 Press the numeric key to enter “9 - 9 - 2”.3 Press the VID2 key twice.• When a re-assignment is done, the LED will blink twice to confirmyour choice. At that time, you will need to program the remotecontrol in order to control the new component.• If an invalid key sequence is entered, the LED blink once and returnto normal operation.• When in Tuner mode, re-assignment is not available.Operating other componentsThis operation lets you operate the registered components.KENWOOD audio components with system control turn on and offautomatically with the receiver via the system control connections.1Use the Source keys to select the component you desire.• Pressing the Source keys also changes the input selector on thereceiver. 7• When you operate your registered DVD player, CD player, Cassettedeck, MD player, Cable, DTV decoders, VCR or TV, go to step 2.• When you operate the CD player, Cassette deck, MD player, orTuner with system control connection, go to step 3.2Press the SRC (source) Power key.• To return to the receiver operation mode, press the TUNER key formore than 3 seconds.3Press the operation keys you desire. ›The remote control mode remains at the selected input. If youwish to operate another component, repeat step 2 or 3.Note• Be sure to point the remote control at the remote sensor on thereceiver when you want to operate KENWOOD componentsconnected by system control cords. Otherwise, point the remotecontrol at the component you want to operate.• To initialize the remote control, press the Remote Setup key untilthe LED blinks twice. Then press the numeric key to enter “9-8-1”.The LED blinks twice.4¢ + ++SRC PowerSourcekeys