Kenwood KRF-V7030D Instruction Manual

Also see for KRF-V4530D: Instruction manual Instruction manual Instruction manual Service manual Service manual

18OperationsMuting the soundThe MUTE key lets you mute the sound of the speakers.Press the MUTE key.To cancelPress the MUTE key again so that the “MUTE” indicator goes off.• Muting can also be canceled by adjusting the volume.BlinksSOURCE DIRECT playback (analog sources only)Use this function to pass the source material direct to the amplifier,bypassing any audio processing.To cancelPress the SOURCE DIRECT key.• When you press the LISTEN MODE, SOUND, or SETUP keys, orswitch to another input source, SOURCE DIRECT playback will becanceled.Listening with headphones1 (KRF-V7030D/V6030D)Press the SPEAKERS A or B key so that the speaker indicatorgoes off.(KRF-V5030D/V4530D)Press the SPEAKER key so that the speaker indicator goes off.Make sure the SPEAKERSindicators are turned off.2 Connect headphones to the PHONES jack.• If you turn off all of the speakers when in the surround mode, themode is cancelled as well, resulting in stereo playback.• The speakers do not switch off during the 6CH INPUT mode.Select the other input mode. 03 Use the VOLUME CONTROL (VOLUME) to adjust the volume.1 Use the INPUT SELECTOR knob to select the source (other than“MD/TAPE”) you want to record.2 Set the cassette deck to record.3 Start playback, then start recording.Recording audio (analog sources)RecordingRecording a music source1 Press the MONITOR key.2 Use the INPUT SELECTOR knob to select a source other than“MD/TAPE.”3 Start playback on the cassette deck connected to the MONITORjacks and start recording on the cassette deck connected to theMD/TAPE jacks.Recording tapes1 Use the INPUT SELECTOR knob to select “MD/TAPE.”2 Start playback on the cassette deck connected to the MD/TAPEjacks and start recording on the cassette deck connected to theVIDEO2/MONITOR jacks.MONITOR = MD/TAPE recordingMD/TAPE = MONITOR recording• To copy tapes using a double cassette deck, refer to the instructionmanual of the double cassette deck.MONITOR function (analog sources only)You can connect a cassette deck or graphic equalizer to the VIDEO2/MONITOR jacks of the receiver. If a graphic equalizer is connected, theMONITOR key should be left in the on position. Alternately, if a cassettedeck equipped with a 3-head system is connected to the VIDEO2/MONITOR jacks, you will be able to monitor the just-recorded signalwhile making recordings on the cassette deck. By switching the MONI-TOR key on and off, you can compare the sound of the source signaland the just-recorded signal. For more information, refer to the instruc-tion manual of the connected component.Press the SOURCE DIRECT key again.• If SOURCE DIRECT playback was activated when using a surroundmode, cancelling it reactivates the previous surround mode.Normal playbackLFECS RSLSTI.VOLBCLIPRDS EON PTYTP TA NEWSSWLSP A RMUTEPHONESINPUT SELECTORMONITORS.DIRECTFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALDSPMEMOST.TUNEDAUTO SOUND AUTOSTEREO MONITORMake sure the SP indicatorsare turned off.KRF-V5030D/V4530DKRF-V7030D/V6030DWhen recording a music source, switch the VIDEO2/MONITORsetting to “MONITOR” (KRF-V6030D/V5030D/V4530D only). 8When recording a music source, switch the VIDEO2/MONITORsetting to “MONITOR” (KRF-V6030D/V5030D/V4530D only). 8STEREOFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOS.DIRECTSWRLLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSP ASWRLLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSASP