8PreparationsMONITORPLAY INPLAY IN REC OUTAUDIOLRMD/TAPE1CD/DVDPHONOGND REC OUTMake connections as shown below.When connecting the related system components, be sureto also refer to the instruction manuals supplied with thecomponents you are connecting.Do not connect the power cord to a wall outlet until allconnections are completed.Connecting audio componentsTo AC wall outletCassette deck orMD recorderCD playerIN OUTSYSTEM CONTROLjacks @Video component,3 head cassette deck, orGraphic equalizer *Setting up the systemINOUTOUTOUTVIDEO2/MONITORjacks (KRF-V6030D/V5030D/V4530D only)You can connectan equalizer inMonitor mode, ora video compo-nent in Video 2mode.When you connect the video component to the VIDEO2/MONI-TOR jacks, connect the video cord (yellow RCA pin cords) of theconnected component to the VIDEO2 IN jack (KRF-V6030D/V5030D/V4530D only).Analog connectionsAudio connections are made using RCA pin cords. These cables transferstereo audio signal in an “analog” form. This means the audio signalcorresponds to the actual audio of two channels. These cables usually have2 plugs each end, one red for the right channel and one white for the leftchannel. These cables are usually packaged with the source unit, or areavailable at your local electronics retailer.Record playerNotes1. Be sure to insert all connection cords securely. If their connections areimperfect, the sound may not be produced or noise may interfere.2. Be sure to remove the power cord from the AC outlet before plugging orunplugging any connection cords. Plugging/unplugging connection cordswithout disconnecting the power cord can cause malfunctions and maydamage the unit.3. Do not connect power cords from components whose power consump-tion is larger than what is indicated on the AC outlet at the rear of this unit.VIDEO 2/MONITOR jacks (for KRF-V6030D/V5030D/V4530D)The receiver’s VIDEO 2/MONITOR jacks can be used in two differentways. Make the appropriate setting for the component connected to thejack when the receiver is turned on.Use as a VIDEO 2 jackYou can connect a video deck or the like to these jacks and performvideo playback and recording. The initial factory setting is “VIDEO 2”.Use as a MONITOR jackYou can connect a cassette deck or the like to these jacks and make useof the deck’s monitoring function during recording. Alternately, you canconnect a graphic equalizer to these jacks to apply compensation to themusic signal.To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold downthe MONITOR key of the main unit for more two seconds so that theindication shown below appears.• At the same time the setting is switched to “MONITOR,” the audio inputsource switches to tuner and the video input source switches to VIDEO1.• To switch the setting back to “VIDEO 2,” once again hold down theMONITOR key for two seconds or more.TUNEDAUTOFMMHzAMkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTDSPAUTO SOUNDLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSTEREO ST.MEMOSWRLSP AMONITORMONITORDTS Digital Surround™ is a discrete 5.1 channel digital audio formatavailable on CD, LD, and DVD software which consequently cannot bedecoded and played back inside most CD, LD, or DVD players. For thisreason, when DTS-encoded software is played back through the analogoutputs of the CD, LD, or DVD player, excessive noise will be exhibited.To avoid possible damage to the audio system, proper precautionsshould taken by the consumer if the analog outputs are connecteddirectly to an amplification system. To enjoy DTS Digital Surround™playback, an external 5.1 channel DTS Digital Surround™ decodersystem must be connected to the digital output (S/P DIF, AES/EBU, orTosLink) of the CD, LD or DVD player.The only audio product model incorporating the DTS Digital Surrounddecoder is the KRF-V7030D.DTS disclaimer clauseShape of AC outletsU. K.Other countries