Kenwood KRF-V7070D Instruction Manual

Also see for KRF-V7070D: Service manual Service manual

17 ENENGLISHPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.1 Turn on the power to this receiver by pressing the POWERON/OFF and ON/STANDBY key or POWER RCVR key.2 For the remote control, press and hold the TUNER key formore than 3 seconds to switch to receiver mode.3 Press the SETUP key to enter the SETUP mode and press∧ / ∨keys or @/ #keys for the following displays.1 SP SETUP2 TEST TONE3 SP DISTANCE4 DISP MODE5 EXITThe flow of the SET UP is as follows:4 Select a speaker system.1 Select the SP SETUP and press the SETUP key again so thatthe subwoofer setting indication “SUBW ON” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate subwoofer setting.1 SUBW ON : Subwoofer setting mode to the receiver isON.2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakersare automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.• When subwoofer output sound is required, select “FRNTNORMAL”, or select both “FRNT LARGE” and “SW RE-MIX ON”.3 Press the ∧ key or # key to accept the setting.• The front speakers setting indication “FRNT” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE4 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate front speakers setting.1 FRNT LARGE : Large front speakers are connectedto the receiver.2 FRNT NORMAL : Average size front speakers areconnected to the receiver.• For “FRNT LARGE” selection, no sound will be heard fromsubwoofer speaker even when it is set to on. However, if youselect “SW RE-MIX ON” when subwoofer is selected, you willbe able to hear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.5 Press the ∧ key or # key to accept the setting.• The center speaker setting indication “CNTR” appears.6 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate center speaker setting.If you selected “LARGE” as the front speakers setting,1 CNTR LARGE : A large center speaker is connectedto the receiver.2 CNTR NORMAL : An average size center speaker isconnected to the receiver.3 CNTR OFF : Center speaker setting mode to thereceiver is OFF.If you selected “NORMAL” as the front speakers setting,1 CNTR ON : Center speaker setting mode to the receiveris ON.2 CNTR OFF : Center speaker setting mode to the receiveris OFF.7 Press the ∧ key or # key again to accept the setting.• The surround speaker indication “SURR” appears.8 Use the MULTI CONTROL knob or Multi (%/fi) to select theappropriate surround speaker setting.If you selected “LARGE” as the center speaker setting,1 SURR LARGE : Large surround speakers areconnected to the receiver.2 SURR NORMAL : Average size surround speakers areconnected to the receiver.3 SURR OFF : Surround speaker setting mode tothe receiver is OFF.SP SETUP TEST TONE SP DISTANCE EXITDISP MODEFront LeftCenterFront RightSurround RightSurround BackSurround LeftSubwooferDisplay SelectorDisplay ListenSubwooferFrontCenterSurroundSurroundBackSurroundMixSubwooferRe-mixT. TONEMANUALT. TONEAUTOLCRSRSLSBSWLCRSRSLSWSBContinued to next pageSETUP MULTI CONTROLPOWER RCVRSetup(Multi %/ fi,@/#)ON/STANDBYPOWER ON/OFFTUNER