Kenwood KRF-X9050D Instruction Manual

Also see for KRF-X9050D: Service manual Service manual

22Preparations45Adjust the speaker volume.From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.1 Use the MULTI CONTROL knob or keys to adjust the volumeof the test tone output from the speaker channel to beadjusted.The channel indication blinks while the test tone is being output.The test tone is heard from the speakers in the followingsequence for 2 seconds each:= L = C = R = SR = SL = SWSTEREOR FMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSLSP AFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSWLSP A RSTEREO• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. ¢• If the speaker setting selects are OFF, the speaker level settingsare reset.2 Press the SET UP key.• The test tone is turned off. The receiver enters the mode forinputing the bass peak level and the current peak level will beshown.• To obtain accurate output levels, it is recommended to use ahandheld Sound Pressure Level (SPL) meter. Readings should betaken from your actual listening position and adjust the level ofeach speaker to 75dB SPL (C-weighted/slow meter mode).Adjust the bass peak level.A restriction is put on the low frequency so that the bass peak level willnot go higher than the acceptable level when the volume is increased.If subwoofer speaker is OFF, the limitation will affect the low frequencyof the front left and right speakers.1 Use the MULTI CONTROL knob or keys to adjust the basspeak level to –30.• The bass peak level may be adjusted from –30dB to 0dB andOFF.• When no subwoofer is in use, the test tone will be output from thefront channel speakers.2 To find the bass peak level limit, keep increasing the basspeak level by using the MULTI CONTROL knob or keys whiletest tone is being output until the clip point of the subwooferis found.3 Press the SET UP key.• The receiver enters the mode for inputing the distance to thespeakers.Preparing for surround sound1 Use the INPUT SELECTOR knob to select the source whichyou want to adjust.• You can store a separate input level for each input source. If theMONITOR function is ON, you can store an input level for whenMONITOR is on independently of the input levels for the inputsources.2 Press the SOUND key repeatedly until the “INPUT” indicationappears.3 Use the MULTI CONTROL knob or keys to adjust the inputlevel.• The adjustment mode is displayed for approximately eight sec-onds.• The input level may be adjusted to any one of three settings: 0dB,-3dB, and -6dB. (The initial setting is 0dB.)4 Press the SOUND key again to return to the input indication.SWFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSLSP A RSTEREOSWRDSTPCLIPIf the input level of an analog source signal is too high, the CLIP indicatorwill blink. Adjust the input level.LFE SWFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOCS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSP A LSTEREOThe speaker indicator to be adjusted blinks.Indication in feet Indication in metersDisplay when all speakers have been selected.LFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSLSP A RSWInput the distance to the speakers.1 Measure the distance from the listening position to each ofthe speakers.Jot down the distance to each of the speakers.Distance to front left speaker : ____ feet (meters)Distance to center speaker : ____ feet (meters)Distance to front right speaker : ____ feet (meters)Distance to surround right speaker : ____ feet (meters)Distance to surround leftt speaker : ____ feet (meters)Distance to subwoofer : ____ feet (meters)2 Use the MULTI CONTROL knob or keys to select the distanceto the front speakers.• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),adjustable in 1 foot (0.3 m) increment.3 Press the SET UP key.4 Repeat steps 2 and 3 to input the distance for each of thespeakers.5 Setup is complete when the input indication reappears.• The speakers you have selected should appear on the display.Confirm that all the speakers have been correctly selected.6STEREOFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFES RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSP ASWInput level adjustment (analog sources only)