Kenwood TK-5310 K4 Service Manual

Also see for TK-5310: Specifications Instruction manual Specifications Instruction manual

Contents

TK-53104REALIGNMENT5. PC Mode5-1. PrefaceThe transceiver is programmed by using a personal com-puter, programming interface (KPG-36/36A), USB adapter(KCT-53U) and programming software (KPG-95D).The programming software can be used with an IBM PCor compatible. Figure 1 shows the setup of an IBM PC forprogramming.5-2. Connection procedure1. Connect the transceiver to the computer using the inter-face cable and USB adapter (When the interface cable isKPG-36A, the KCT-53U can be used.).Notes:• You must install the KCT-53U driver in the computer to usethe USB adapter (KCT-53U).• When using the USB adapter (KCT-53U) for the first time,plug the KCT-53U into a USB port on the computer withthe computer power ON.2. When the POWER switch on, user mode can be enteredimmediately. When PC sends command the transceiverenter PC mode, and “PROGRAM” is displayed on the LCD.When data transmitting from transceiver, the red LED is lights.When data receiving to transceiver, the green LED is lights.Notes:• The text message are displayed for K2, K3, K5 and K6 mod-els only.• The data stored in the computer must match the "ModelName and Market Code" when it is written into theEEPROM and flash memory.5-3. KPG-36/KPG-36A description(PC programming interface cable: Option)The KPG-36/36A is required to interface the transceiver tothe computer. It has a circuit in its D-sub connector (KPG-36: 25-pin, KPG-36A : 9-pin) case that converts the RS-232Clogic level to the TTL level.The KPG-36/36A connects the universal connector of thetransceiver to the RS-232C serial port of the computer.5-4. KCT-53U description (USB adapter : Option)The KCT-53U is a cable which connects the KPG-36A to aUSB port on a computer.When using the KCT-53U, install the supplied CD-ROM(with driver software) in the computer. The KCT-53U driverruns under Windows 2000 or XP.5-5. Programming software KPG-95D descriptionThe KPG-95D is the programming software for the trans-ceiver supplied on a CD-ROM. This software runs under MS-Windows 98, ME, Windows 2000 or XP on an IBM-PC orcompatible machine.The data can be input to or read from the transceiver andedited on the screen. The programmed or edited data can beprinted out. It is also possible to tune the transceiver.6. Firmware Programming Mode6-1. PrefaceFlash memory is mounted on the transceiver. This allowsthe transceiver to be upgraded when new features are re-leased in the future. (For details on how to obtain the firm-ware, contact Customer Service.)6-2. Connection procedureConnect the transceiver to the personal computer (IBMPC or compatible) using the interface cable (KPG-36/36A) andUSB adapter (KCT-53U : when the interface cable is KPG-36A, the KCT-53U can be used.). (Connection is the same asin the PC Mode.)6-3. Programming1. Start up the firmware programming software (Fpro.exe).2. Set the communications speed (normally, 115200 bps)and communications port in the configuration item.3. Set the firmware to be updated by File name item.4. Press and hold the [Side3] and [PTT] keys while turningthe transceiver power ON and then release the [Side3] keyfirst. Then, the orange LED on the transceiver lights andthe baud rate is displayed as follows according to the posi-tion of the Concentric switch.A: PROGRAM 115200 bpsB: PROGRAM 57600 bpsC: PROGRAM 19200 bpsSince the baud rate is normally set to 115200 bps, changethe Concentric switch to "A".5. Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.6. Press “write” button in the window. When the trans-ceiver starts to receive data, the [PG] display lights.Fig. 1IBM-PCKPG-95DKPG-36 or KPG-36A orKPG-36A + KCT-53UIllustration is KPG-36.KPG-36TransceiverPCD-SUB(25-pin)TransceiverPCKPG-36AD-SUB(9-pin)TransceiverPCKPG-36AKCT-53UUSB