Kenwood TS-870S Instruction Manual

Also see for TS-870S: Instruction manual Operation manual Instruction manual Instruction manual In-depth manual

Contents

92● APPENDICES1Sets or reads transmit monitor level.ML TRANSMIT MONITOR LEVEL2Parameter Format Parameter functionP1 46 TRANSMITMONITORLEVEL3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3M L P1M L P1 ;M L ;4 5 6 7 8 9 10 11 12 13 14;1Sets Lock OFF/ON or reads status.LK LOCK2Parameter Format Parameter functionP1 1 LOCK OFF/ON3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3L K P1L K P1 ;L K ;4 5 6 7 8 9 10 11 12 13 14;1DRS recordingLM LOAD MESSAGE2Parameter Format Parameter functionP1 45 LOADMESSAGE3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3L M P1L M P1 ;L M ;4 5 6 7 8 9 10 11 12 13 14;1Sets Transmit Monitor OFF/ON or reads status.MN TRANSMIT MONITOR2Parameter Format Parameter functionP1 1 TRANSMITMONITOROFF/ON3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3M N P1M N P1 ;M N ;4 5 6 7 8 9 10 11 12 13 14;1Sets or reads memory channels.MC MEMORY CHANNEL2Parameter Format Parameter functionP1 _ NOT USED3 4 5 6 7 8 9 10 11 12 13 14ut FunctionSetM C ;MEMORY CHANNEL7P2P21Reads memory.MR MEMORY READ2Parameter Format Parameter functionP1P2P3P4P5P6P7P8P99–74210114–SPLIT DATANOT USEDMEMORY CHANNELFREQUENCYMODEMEMORY LOCKOUTTONE OFF/ONTONE NUMBERNOT USED3 4 5 6 7 8 9 10 11 12 13 1415Input commands FunctionOutput commandsSetcommandReadcommandAnswer command16 17 18 19 20 21 22 23 24 25 26 27 281 2 3M R ;4 5 6 7 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 24 25 26 27 281 2 3 4 5 6M R P17 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 24 25 26 27P32829 30 31 32 33 34P8P7P535P636 37 38 39 40 41 42P4;P1 P3 Note:For a vacant channel, the Answer commandsends "0" for all parameters except thememory channel number.P1 must be "0" to read the CH 99 Startfrequency and "1" to read the End frequency.1Sets or reads modes.MD MODE2Parameter Format Parameter functionP1 2 MODE3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3M D P1M D P1 ;M D ;4 5 6 7 8 9 10 11 12 13 14;1Sets or reads MIC gain.MG MIC GAIN2Parameter Format Parameter functionP1 31 MIC GAIN3 4 5 6 7 8 9 10 11 12 13 14Input FunctionOutputSetReadAnswer1 2 3 4 5 6 7 8 9 10 11 12 13 141 2 3M G P1 ;M G ;4 5 6 7 8 9 10 11 12 13 14P1M G ;1Writes into memory.Note:All parameters must be entered.The memory channel becomes a vacantchannel if all frequency digits are "0".Other parameters are ignored.P1 must be "0" to store a Start frequencyand "1" to store an End frequency.MW MEMORY WRITE2Parameter Format Parameter functionP1P2P3P4P5P6P7P8P99–74210114–SPLIT DATANOT USEDMEMORY CHANNELFREQUENCYMODEMEMORY LOCKOUTTONE OFF/ONTONE NUMBERNOT USED3 4 5 6 7 8 9 10 11 12 13 1415Input commands FunctionOutput commandsSetcommandReadcommandAnswer command16 17 18 19 20 21 22 23 24 25 26 27 281 2 3 4 5 6 7 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 24 25 26 27 281 2 3 4 5 6M W P17 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 24 25 26 27P32829 30 31 32 33 34P8P7P535P636 37 38 39 40 41 42P4;