Makita DCU604 Instruction Manual

Also see for DCU603: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

24 ENGLISHInstalling or removing the dump unitOptional accessoryInstalling the dump unit1. Take out the dump unit and the handle from the box.► Fig.8: 1. Dump unit 2. Handle2. Insert the pipes of the handle into the dump unit asshown in the figure, and then tighten 4 bolts securely.► Fig.9: 1. Bolt 2. HandleNOTE: When tightening the bolts, lift the handleslightly.3. Make sure that the dump unit is locked by pullingdown the handle.► Fig.10: 1. Handle4. Remove the cord cover located in the lower rightcorner on the rear of the machine.► Fig.11: 1. Cord cover5. Place the dump unit on the base unit by holdingthe dump unit with two people as shown in the figure.► Fig.126. Temporarily tighten 2 bolts at the rear of themachine. Tighten the rest of 4 bolts securely, and thentighten 2 bolts at the rear of the machine securely.► Fig.13: 1. Bolt (front) 2. Bolt (rear)7. Attach the cord cover.► Fig.14: 1. Cord coverRemoving the dump unitTo remove the dump unit, perform the installation proce-dure in reverse.Installing or removing the bucketOptional accessoryInstalling the bucket1. Take out the bucket, stays, and front pipe from the box.► Fig.15: 1. Bucket 2. Stay 3. Front pipe2. Insert the front pipe between the upper frame andlower frame of the dump unit.► Fig.16: 1. Front pipe3. Place the stay on the dump unit, and then tempo-rarily tighten the bolts with the front pipe together. Installthe other stay to the dump unit in the same way.► Fig.17: 1. Stay 2. Bolt4. Place the bucket on the front pipe and left and right stays.Place the rubber washer on the hole of the bucket andinsert the bolt from the top. Attach the flat washer andspring washer in order to the bolt, and then tighten thenut from the bottom. Tighten the rest of the bolts andnuts in the same way.► Fig.18: 1. Bolt 2. Rubber washer 3. Flat washer4. Spring washer 5. Nut5. Securely tighten 4 bolts which were temporarilytightened in step 3.Removing the bucketTo remove the bucket, perform the installation proce-dure in reverse.Installing or removing the carrierOptional accessoryInstalling the carrier1. Take out the carrier from the box, and attach theside rails and front rail to the base frame.► Fig.192. Tighten 6 thumb nuts together with springs andwashers to fix the rails.► Fig.20: 1. Thumb nut 2. Spring 3. Washer3. Place the carrier on the dump unit.Insert the bolt from the top. Attach the flat washer andspring washer in order to the bolt, and then tighten thenut from the bottom. Tighten the rest of the bolts andnuts in the same way.► Fig.21: 1. Bolt 2. Flat washer 3. Spring washer4. NutRemoving the carrierTo remove the carrier, perform the installation proce-dure in reverse.Installing or removing the flatbucketOptional accessoryInstalling the flat bucket1. Take out the flat bucket and holding frames fromthe box.► Fig.22: 1. Flat bucket 2. Holding frame2. Assemble the holding frames by tightening 12bolts.► Fig.23: 1. Bolt3. Remove the cord cover located in the lower rightcorner on the rear of the machine.► Fig.24: 1. Cord cover4. Place the holding frames on the base unit, andthen temporarily tighten 2 bolts at the rear of themachine. Tighten the rest of 4 bolts securely, and thentighten 2 bolts at the rear of the machine securely.► Fig.25: 1. Bolt (front) 2. Bolt (rear)5. Attach the cord cover.► Fig.26: 1. Cord cover6. Hold the long sides of the flat bucket with twopeople as shown in the figure, and mount the flat bucketto the holding frames.► Fig.27Removing the flat bucketTo remove the flat bucket, perform the installation pro-cedure in reverse.