Makita DTL060 Instruction Manual

Also see for DTL060: Instruction manual Instruction manual Technical information Instruction manual Instruction manual

Contents

62. Always be sure you have a firm footing.Be sure no one is below when using the tool inhigh locations.3. Hold the tool firmly.4. Wear ear protectors.5. Do not touch the bit or the workpiece immediatelyafter operation. They may be extremely hot andcould burn your skin.6. Keep hands away from rotating parts.7. Use auxiliary handle(s), if supplied with the tool.Loss of control can cause personal injury.8. Hold the power tool by insulated grippingsurfaces, when performing an operation where thecutting accessory may contact hidden wiring.Cutting accessory contacting a “live” wire may makeexposed metal parts of the power tool “live” and couldgive the operator an electric shock.SAVE THESE INSTRUCTIONS.WARNING: DO NOT let comfort or familiarity withproduct (gained from repeated use) replace strictadherence to safety rules for the subject product.MISUSE or failure to follow the safety rules stated inthis instruction manual may cause serious personalinjury.IMPORTANT SAFETYINSTRUCTIONS FOR BATTERYCARTRIDGE ENC007-121. Before using battery cartridge, read allinstructions and cautionary markings on (1)battery charger, (2) battery, and (3) product usingbattery.2. Do not disassemble battery cartridge.3. If operating time has become excessively shorter,stop operating immediately. It may result in a riskof overheating, possible burns and even anexplosion.4. If electrolyte gets into your eyes, rinse them outwith clear water and seek medical attention rightaway. It may result in loss of your eyesight.5. Do not short the battery cartridge:(1) Do not touch the terminals with anyconductive material.(2) Avoid storing battery cartridge in a containerwith other metal objects such as nails, coins,etc.(3) Do not expose battery cartridge to water orrain.A battery short can cause a large current flow,overheating, possible burns and even abreakdown.6. Do not store the tool and battery cartridge inlocations where the temperature may reach orexceed 50°C (122°F).7. Do not incinerate the battery cartridge even if it isseverely damaged or is completely worn out. Thebattery cartridge can explode in a fire.8. Be careful not to drop or strike battery.9. Do not use a damaged battery.10. The contained lithium-ion batteries are subject tothe Dangerous Goods Legislation requirements.For commercial transports e.g. by third parties,forwarding agents, special requirement on packagingand labeling must be observed.For preparation of the item being shipped, consultingan expert for hazardous material is required. Pleasealso observe possibly more detailed nationalregulations.Tape or mask off open contacts and pack up thebattery in such a manner that it cannot move around inthe packaging.11. Follow your local regulations relating to disposalof battery.12. Use the batteries only with the products specifiedby Makita. Installing the batteries to non-compliantproducts may result in a fire, excessive heat,explosion, or leak of electrolyte.SAVE THESE INSTRUCTIONS.CAUTION: Only use genuine Makita batteries.Use of non-genuine Makita batteries, or batteries thathave been altered, may result in the battery burstingcausing fires, personal injury and damage. It will also voidthe Makita warranty for the Makita tool and charger.Tips for maintaining maximum battery life1. Charge the battery cartridge before completelydischarged.Always stop tool operation and charge the batterycartridge when you notice less tool power.2. Never recharge a fully charged battery cartridge.Overcharging shortens the battery service life.3. Charge the battery cartridge with roomtemperature at 10°C - 40°C (50°F - 104°F). Let a hotbattery cartridge cool down before charging it.4. Charge the battery cartridge if you do not use it fora long period (more than six months).FUNCTIONAL DESCRIPTIONCAUTION:• Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function on the tool.Installing or removing battery cartridge(Fig. 1)• Always switch off the tool before installing or removingof the battery cartridge.• To remove the battery cartridge, slide it from the toolwhile sliding the button on the front of the cartridge.• To install the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. Always insert it all the way until it locks inplace with a little click. If you can see the red indicatoron the upper side of the button, it is not lockedcompletely. Install it fully until the red indicator cannotbe seen. If not, it may accidentally fall out of the tool,causing injury to you or someone around you.• Do not use force when installing the battery cartridge. Ifthe cartridge does not slide in easily, it is not beinginserted correctly.