Makita LS1013 Instruction Manual
Also see for LS1013: Instruction manualInstruction manualParts BreakdownInstruction manualInstruction manual
                                                                                                                        | |
12• When not using the tool, remove the lock-off buttonand store it in a secure place. This preventsunauthorized operation.• Do not pull the switch trigger hard without pressingin the lock-off button. This can cause switchbreakage.For European countriesFig.13To prevent the switch trigger from being accidentallypulled, a lock-off button is provided. To start the tool,push the lever to the left, press in the lock-off button andthen pull the switch trigger. Release the switch trigger tostop.For all countries other than European countriesFig.14To prevent the switch trigger from being accidentallypulled, a lock-off button is provided. To start the tool,press in the lock-off button and pull the switch trigger.Release the switch trigger to stop.WARNING:• NEVER use tool without a fully operative switchtrigger. Any tool with an inoperative switch isHIGHLY DANGEROUS and must be repairedbefore further usage.• For your safety, this tool is equipped with a lock-offbutton which prevents the tool from unintendedstarting. NEVER use the tool if it runs when yousimply pull the switch trigger without pressing thelock-off button. Return tool to a Makita servicecenter for proper repairs BEFORE further usage.• NEVER tape down or defeat purpose and functionof lock-off button.Lighting up the lampsFor Model LS1013F,LS1013FL onlyFig.15CAUTION:• This is not a rainproof light. Do not wash the light inwater or use it in a rain or a wet area. Such aconduct can cause an electric shock and fume.• Do not touch the lens of the light, as it is very hotwhile it is lighted or shortly after it is turned off. Thismay cause a burn to a human body.• Do not apply impact to the light, which may causedamage or shorted service time to it.• Do not keep casting the beam of the light to youreyes. This can cause your eyes to be hurt.• Do not cover the light with clothes, carton,cardboard or similar objects while it is lighted,which can cause a fire or an ignition.Push the upper position of the switch for turning on thelight and the lower position for off.Fig.16Move the light to shift an area of lighting.NOTE:• Use a dry cloth to wipe the dirt off the lens of lamp.Be careful not to scratch the lens of light, or it maylower the illumination.Laser beam actionFor model LS1013L,LS1013FL onlyFig.17CAUTION:• Never look into the laser beam. Direct laser beammay injure your eyes.• LASER RADIATION, DO NOT STARE INTO THEBEAM OR VIEW DIRECTLY WITH OPTICALINSTRUMENTS, CLASS 2M LASER PRODUCT.To turn on the laser beam, press the upper position (I) ofthe switch. Press the lower position (O) to turn off.Laser line can be shifted to either the left or right side ofthe saw blade by adjusting the adjusting screw asfollows.Fig.181. Loosen the adjusting screw by turning itcounterclockwise.2. With the adjusting screw loosened, slide theadjusting screw to the right or left as far as it goes.3. Tighten the adjusting screw firmly at the positionwhere it stops sliding.Laser line is factory adjusted so that it is positionedwithin 1 mm from the side surface of the blade (cuttingposition).NOTE:• When laser line is dim and almost or entirelyinvisible because of the direct sunlight in the indooror outdoor window-by work, relocate the work areato a place not exposed to the direct sunlight.Aligning the laser lineFig.19Laser line can be shifted to either the left or right side ofthe blade according to the applications of cutting. Referto explanation titled "Laser beam action" regarding itsshifting method.NOTE:• Use wood facing against the guide fence whenaligning the cutting line with the laser line at theside of guide fence in compound cutting (bevelangle 45 degrees and miter angle right 45degrees).A) When you obtain correct size on the left side ofworkpiece• Shift the laser line to the left of the blade.B) When you obtain correct size on the right side ofworkpiece• Shift the laser line to the right of the blade.Align the cutting line on your workpiece with the laserline. |
Related manuals for Makita LS1013
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
manualsdatabase
Your AI-powered manual search engine