Makita RT001GM210 Instruction Manual

Also see for RT001G: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

22 ENGLISHChanging the collet coneCAUTION: Use the correct size collet cone forthe trimmer bit which you intended to use.CAUTION: Do not tighten the collet nut withoutinstalling a trimmer bit, or the collet cone may break.1. Loosen the collet nut and remove.2. Replace the installed collet cone with desired collet cone.3. Reinstall collet nut.► Fig.9: 1. Collet cone 2. Collet nutInstalling or removing the trimmer base1. Open the lock lever of the trimmer base, theninsert the tool into the trimmer base aligning the grooveon the tool with the protrusion on the trimmer base.2. Close the lock lever.► Fig.10: 1. Lock leverNOTE: You can use the trimmer base (resin) as anoptional accessory as shown in the figure. Whenusing the trimmer base (resin), loosen or tighten thethumb nut instead of opening or closing the lock lever.Align the rack on the tool with the spur gear on thetrimmer base.► Fig.11: 1. Thumb nut 2. Rack 3. Spur gear3. Attach the dust nozzle to the trimmer base, andthen tighten the thumb screw.► Fig.12: 1. Dust nozzle 2. Thumb screw► Fig.13To remove the base, follow the installation procedurein reverse.CAUTION: When using the tool with the trim-mer base, be sure to install the dust nozzle on thetrimmer base.Installing or removing the tilt baseOptional accessory1. Open the lock lever of the tilt base, then insert thetool into the tilt base aligning the groove on the tool withthe protrusion on the tilt base.2. Close the lock lever.► Fig.14: 1. Lock leverTo remove the base, follow the installation procedurein reverse.Installing or removing the offset baseOptional accessory1. Press the shaft lock, then loosen the collet nut.► Fig.15: 1. Collet nut 2. Shaft lock 3. Wrench2. Remove the collet nut and the collet cone.► Fig.16: 1. Collet nut 2. Collet cone3. Install the pulley onto the tool by pressing theshaft lock and tightening the pulley with the wrench.► Fig.17: 1. Wrench 2. Pulley 3. Shaft lock4. Loosen the screws on the base plate, and thenremove the base plate.► Fig.18: 1. Base plate5. Open the lock lever of the offset base, then attachthe offset base to the tool.► Fig.19: 1. Lock lever6. Mount the belt to the pulley with a stick like aslotted screwdriver by rotating the belt manually.► Fig.20: 1. Pulley 2. Belt7. Close the lock lever.► Fig.21: 1. Lock lever8. Attach the base plate by tightening the screws.► Fig.22: 1. Base plate9. Insert the collet cone and the trimmer bit into theoffset base, and then tighten the collet nut.► Fig.23: 1. Trimmer bit 2. Collet nut 3. Collet cone10. Insert the hex wrench into the hole of the offsetbase, and then tighten the collet nut with the wrench.► Fig.24: 1. Collet nut 2. Wrench 3. Hex wrenchTo remove the base, follow the installation procedurein reverse.NOTE: You can also mount the belt to the pulley with-out removing the base plate as shown in the figure.► Fig.25: 1. Pulley 2. BeltInstalling or removing the plungebaseOptional accessory1. Open the lock lever of the plunge base, then insertthe tool into the plunge base all the way aligning thegroove on the tool with the protrusion on the plungebase.2. Close the lock lever.► Fig.26: 1. Lock leverTo remove the base, follow the installation procedurein reverse.Installing or removing the parallelruler on the plunge baseOptional accessoryInsert the guide bars into the holes in the plunge base,and then tighten the wing bolts. To remove the ruler,follow the installation procedure in reverse.► Fig.27: 1. Wing bolt 2. Guide barInstalling or removing the dustnozzle on the plunge baseInsert the dust nozzle into the plunge base so that theprotrusion on the dust nozzle fits in the notch in theplunge base, and then tighten the thumb screw on thedust nozzle. To remove the nozzle, follow the installa-tion procedure in reverse.► Fig.28: 1. Protrusion 2. Dust nozzle 3. Thumbscrew► Fig.29