Makita WST01N Instruction Manual

3ENGLISHModels:LS0714, LS0815, LS1013, LS1016, LS1017, LS1018, LS1019, LS1214, LS1216, LS1219, LS1040, LS1221, LXSL01,XSL02, XSL03, XSL04, XSL06Inclusive of models followed by F, L and FL, if any.PreparationNote: Check contents of package for the following components. Please inform Makita service center of any part missing inthe package immediately.• Miter saw stand assembly (1 unit)• Hex wrench 6 (1 pc.)• Wrench 13 (1pc.)• Hex socket bolt M8 x 16 (4 pcs.)• Hex socket bolt M8 x 30 (4 pcs.)• Hex bolt M8 x 50 (4 pcs.)• Flat washer 8 (4 pcs.)• Wheel 300 (2 pcs.)• Flat washer 8 (2 pcs.)• Foot arm (1 pc.)• Handle (1 pc.)• Adjusting bolt (2 pcs.)• Clamping nut M12 (2 pcs.)Explanation of general viewSymbols............. Read instruction manual.............. Maximum allowable loadingCAUTION:• Read and thoroughly understand this manual and theinstruction manual of the tool you use beforeperforming the following.• Before installing a tool on this stand, always switch offand unplug the tool.• The stand should be bolted in a stable and levelsurface using the right angle brackets provided on twoof four feet.• Use only with Makita model indicated in the instructionmanual.• Use only the handle to avoid pinched fingers whenraising or folding the stand.• Before operating the tool, secure it to stand using bolts.• Do not use the stand on uneven or unstable surface.• Do not climb, sit or stand on the stand.• When setting up the miter saw stand in the uprightposition or folding it, be sure to securely keep pressingthe pipe of miter saw stand with your foot until it locks.• When storing miter saw stand, never lean it against thewall or the like lengthwise or sideways.• Never pull the locking lever without holding the handle.Assembling miter saw stand (Fig. 1)Assemble parts for miter saw stand as disassembledparts are packed in the carton box.(1) Adjusting boltPlace the stand assembly upright and insert adjustingbolts (2 pcs.) from the below and secure these boltsby tightening nuts.To adjust, turn the adjusting bolts until it reaches floorso that the miter saw stand can be kept stable.(2) Wheel 300 (2 pcs.)Insert the wheels onto the leg B of miter saw stand onboth sides and secure the wheels by tightening hexsocket bolt M8 x 16 (2 pcs.) with washer 8 (2 pcs.)from upper side.(3) Foot armInsert the foot arm onto the port of the leg B fromupper side and secure it by tightening hex socket boltM8 x 16 (2 pcs.) from backside.(4) HandleInsert the handle onto the miter saw stand from thecover side and secure it by tightening hex socket boltM8 x 30 (4 pcs.) from the ratchet cover side.Installing a miter saw on the miter sawstand: (Fig. 2)Place a miter saw so that the hole in the miter saw baseoverlaps a hole in the label on the miter saw stand tableaccording to applicable models. Secure the miter sawstand with hex bolt M8 x 50 (4 pcs.) and flat washer 8(4 pcs.).How to use miter saw standSetting up: (Fig. 3)1. Grip the handle and place your foot on the pipe of theleg A of miter saw stand.2. Release the locking lever with left hand while pressingdown the handle.1. Wheel 3002. Foot arm3. Handle4. Adjusting bolt5. Hex socket bolt M8 x 166. Flat washer 87. Leg B8. Leg A9. Hex socket bolt M8 x 3010. Hex bolt M8 x 5011. Locking lever12. Shift lever13. Pin 10-6014. Stopper15. Extension arm16. Lever 4017. Clamping screw M8 x 2018. Leg pipe 28(220 lbs.)100KgMAX.