© MuxLab Inc. 94-000748-A SE-000748-A8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: videoease@muxlab.com URL: www.muxlab.comSpecificationsEnvironment HDMI 1.3aDevices DVD, plasma, projectors, monitors, TV, PC, laptops, servers supportingHDMI.Transmission Transparent to the userBandwidth 225 MHzSignals HDMI 1.3a protocolConnectors One (1) HDMI receptacle.One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.One (1) 3.5mm jacks for IR emitter/sensor.Four (4) DIP Switches for device ID addressing.Note: HDMI cables not included.Maximum DistanceBased on a maximumlength of 6.6 ft (2 m) ofHDMI cable per end.Cat5e/6: 330 ft (100 m) up to 1080PNote: When installed in an electrically noisy environment, an STP cablemust be used. Also, cross-connection reduces the effective distancedepending on the grade of twisted cable used.Latency One (1) FrameCompression Motion JPEGBandwidth 60MbpsNetwork Requirement 100BaseT for Point to Point; 1000BaseT for other configurationIR Frequency 38KHzRJ45 Pin ConfigurationReverse PolaritySensitive. Use EIA/TIA568A or 586B straight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Cable One (1) Cat 5e/6 or better twisted pair cables requiredPower Supply Two (2) 110-240V/5VDC power supplies with interchangeable bladesPoE IEEE 802.3afPower Consumption Transmitter: 2.9 Watt Receiver: 1.8 WattTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingEnclosure MetalDimensions 3.70” x 3.68” x 0.97” (94 x 93.5 x 24.6 mm)Weight 1.1 lb (0.5 kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 2 yearsOrder Information 500752 HDMI Over IP Extender Kit with PoE500752-TX HDMI Over IP Encoder with PoE500752-RX HDMI Over IP Decoder with PoEHDMI over IP Extender Kit with PoE500752Quick Installation GuideOverviewThe HDMI over IP Extender Kit with PoE (500752) allows HDMI equipment to be connected up to330 ft (100 m) @ 1080p via one (1) Cat 5e/6 unshielded twisted pair cable in a point-to-pointconfiguration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting severalencoders and decoders to the same Ethernet network. The Encoder (500752-TX) and Decoder(500752-RX) also support PoE (PD) if used with a PoE Ethernet Switch. The kit comes with one(1) Encoder and one (1) Decoder as well as an IR Emitter and IR Sensor for remote controlapplications.For the multipoint-to-multipoint configuration the gigabit Ethernet switch must support the IGMPcommunications protocol.ApplicationsApplications include commercial and residential AV systems, classroom projector systems, digitalsignage, boardroom systems, collaborative PC systems, and medical information systems.Installation1. Identify the connectors on the Encoder and Decoder as indicated on the product labels.