MuxLab 500759 Quick Installation Manual
Also see for 500759: Quick installation guideQuick setup guide
Contents |
© MuxLab Inc. 94-000829-A SE-000829-A8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: videoease@muxlab.com URL: www.muxlab.comSpecificationsEnvironment HDMI 1.4Devices Blu-Ray, projectors, monitors, TV, PC, laptops, servers supporting HDMI.Transmission Transparent to the user.Bandwidth 300MHzSignals HDMI 1.4 protocolConnectorsNote: Cables not included.One (1) HDMI receptacle.One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.Two (2) 3.5mm jacks for IR emitter (on TX)/sensor (on RX).Two (2) 3.5mm jacks for audio insert (on TX)/audio extract (on RX)One (1) DB9 for the RS232.Four (4) DIP Switches for device ID addressing.Maximum DistanceBased on a maximum lengthof 6.6ft (2m) of HDMI cableper end.Cat5e/6: 330 ft (100 m) up to 4K @ 30Hz.Note: When installed in an electrically noisy environment, an STP cable must beused. Also, cross-connection reduces the effective distance depending on thegrade of twisted cable used.Latency Typical one (1) Frame (16ms), maximum 2 frames (33ms).Compression Proprietary Compression.Bandwidth Up to 850Mbps.Network Requirement 1000BaseT with Jumbo Frame.IR Frequency 38 to 56 KHz (IR Emitter and IR Sensor sold separately).RJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Cable One (1) Cat 5e/6 or better twisted pair cables required.Power Supply This device supports PoE (PD), an external power supply is not included. It isintended to be powered via a PoE (PSE) Ethernet Switch. If required, an optionalpower supply (500993) may be purchased separately.PoE IEEE 802.3afPower Consumption Transmitter: 2.85Watt Receiver: 2.55WattTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingDimensions 4.40” x 5.08” x 1.00” (112mm x 129mm x 25mm)Weight 1.5lbs (0.68kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 2 yearsOrder Information 500759 Video Wall 4K over IP PoE Extender Kit500759-TX Video Wall 4K over IP PoE Extender TX500759-RX Video Wall 4K over IP PoE Extender RXAccessories(These items are soldseparately)500920 16-Port Rackmount Transceiver Chassis500917 Wall Mount Transceiver Bracket Kit500990 IR Emitter, and 500991 IR Sensor500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU BladeVideo Wall 4K over IP PoE Extender Kit500759Quick Installation GuideOverviewThe Video Wall 4K over IP PoE Extender Kit allows HDMI equipment supporting up to 4K @30Hz or 1080p at 60Hz resolution to be connected and extended to create a Video Wall of userconfigurable size (X by Y) supporting 100’s of screens, depending on network bandwidth, utilizingone Receiver for each display in the array. Each Transmitter (500759-TX) and Receiver (500759-RX) can be connected via Cat5e/6 cable up to 330ft (100m) from an Ethernet Switch.The Transmitters and Receivers support PoE (PD) and may be powered by a PoE (PSE) EthernetSwitch. The kit comes with one (1) Transmitter and one (1) Receiver. The IR Emitter and IRSensor, if required, may be purchased separately for IR based remote control applications.For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet switch musthave Gigabit ports, DHCP server capability, IGMP communications protocol and support JumboFrames. MuxLab recommends using the Cisco SG300 Series Managed Switches.The MuxLab Pro Digital Network Controller (500811) is available to simplify configuration andcontrol and allows for third party smartphone and tablet management.ApplicationsApplications include video wall, digital signage, commercial and residential AV systems,classroom projector systems, boardroom systems, collaborative PC systems, and medicalinformation systems.Installation1. Identify the connectors on the Transmitter and Receiver as indicated on the product labels, see theabove front and rear product views for further details.2. Verify that the distance between the HDMI Transmitter and Receiver is within MuxLabspecifications (see Specifications table for more details).3. To install the Transmitter:3a. Connect the Transmitter to the HDMI video source with an HDMI compliant cable.3b. If the application is point-to-point, then connect one (1) length of Cat 5e/6 (or higher)grade UTP cable to the RJ45 LINK connector on the Transmitter. If transmitting overthe network, use an Ethernet Switch between Transmitter and Receiver4. To install the Receiver:4a. Connect the Receiver to the HDMI display equipment with an HDMI compliant cable.4b. If the application is point-to-point, then connect one (1) Cat 5e/6 cable (or higher)coming from the Transmitter, to the RJ45 LINK connector on the Receiver. If |
Related manuals for MuxLab 500759
MuxLab 500759-TX Quick Installation Manual
MuxLab 500754 Quick Installation Manual
MuxLab 500753 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
MuxLab 500758 Quick Installation Manual
MuxLab 500757 Quick Installation Manual
MuxLab 500757 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
MuxLab 500758 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine