MuxLab 500753 Quick Installation Manual
Also see for 500753: Quick installation guideQuick setup guide
© MuxLab Inc. 94-000786-B SE-000786-B8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: videoease@muxlab.com URL: www.muxlab.comSpecificationsEnvironment HDMI 1.3aDevices DVD, plasma, projectors, monitors, TV, PC, laptops, servers supporting HDMI.Transmission Transparent to the userVideo Bandwidth 225MHzSignals HDMI 1.3a protocolConnectors One (1) HDMI receptacle.One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.One (1) 3.5mm jacks for IR emitter/sensor.One (1) DB9 Serial Port ConnectorFour (4) DIP Switches for device ID addressing.Note: HDMI cables not included.Maximum DistanceBased on a maximum lengthof 6.6ft (2m) of HDMI cableper end.Cat5e/6: 330ft (100m) up to 1080PNote: When installed in an electrically noisy environment, an STP cable must beused. Also, cross-connection reduces the effective distance depending on thegrade of twisted cable used.Latency One (1) FrameCompression Motion JPEGNetwork Bandwidth 60MbpsNetwork Requirement 100BaseT for Point to Point; 1000BaseT for other configurationIR Frequency 38 to 56KHzRJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Cable One (1) Cat 5e/6 or better twisted pair cables requiredPower Source This device supports PoE (PD), an external power supply is not included. It isintended to be powered via a PoE (PSE) Ethernet Switch. If required, an optionalpower supply (500992) may be purchased separately.PoE IEEE 802.3afPower Consumption Transmitter: 2.9Watt Receiver: 1.8WattTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingEnclosure MetalDimensions 3.70” x 3.68” x 0.97” (94 x 93.5 x 24.6mm)Weight 1.1lbs (0.5kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 2 yearsOrder Information 500753 HDMI / RS232 Over IP Extender Kit with PoE500753-TX HDMI / RS232 Over IP Encoder with PoE500753-RX HDMI / RS232 Over IP Decoder with PoEAccessories(These items are soldseparately)500905 3-Port Rackmount Transceiver Chassis500920 16-Port Rackmount Transceiver Chassis500917 Wall Mount Transceiver Bracket Kit500990 IR Emitter, and 500991 IR Sensor500992 Univ. Power Supply 5VDC/1.2A US/UK/EU Blade500753 HDMI / RS232 over IP Extender Kit with PoEQuick Installation GuideOverviewThe HDMI / RS232 over IP Extender Kit with PoE (500753) allows HDMI equipment to beconnected up to 330ft (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in apoint-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible byconnecting several Transmitters and Receivers to the same Ethernet network. The Transmitter(500753-TX) and Receiver (500753-RX) also support PoE (PD) if used with a PoE (PSE) EthernetSwitch. The kit comes with one (1) Transmitter and one (1) Receiver. The IR Emitter and IRSensor, if required, may be purchased separately for IR based remote control applications.For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch musthave Gigabit ports and DHCP Server capability and additionally support the IGMP communicationprotocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300Series Managed Switches.The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration andutilization of the 500753 and other MuxLab IP based products via an Ethernet web interface.ApplicationsApplications include commercial and residential AV systems, classroom projector systems, digitalsignage, boardroom systems, collaborative PC systems, and medical information systems.Installation1. Identify the connectors on the Transmitter and Receiver as indicated on the product labels.2. Verify that the distance between the HDMI Transmitter and Receiver is within MuxLabspecifications (see Specifications table for further details).3. To install the Transmitter:3a. Connect the Transmitter to the HDMI video source with an HDMI compliant cable.3b. If the application is point-to-point, then connect one (1) length of Cat 5e/6 (orhigher) grade UTP cable to the RJ45 LINK connector on the Transmitter. Iftransmitting over the network, use an Ethernet Switch between Transmitter andReceiver.4. To install the Receiver:4a. Connect the Receiver to the HDMI display equipment with an HDMI compliantcable.4b. If the application is point-to-point, then connect one (1) Cat 5e/6 cable (or higher)coming from the Transmitter, to the RJ45 LINK connector on the Receiver. Iftransmitting over the network, use an Ethernet Switch between Transmitter andReceiver. |
Related manuals for MuxLab 500753
MuxLab 500753 Quick Installation Manual
MuxLab 500759 Quick Installation Manual
MuxLab 500757 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
MuxLab 500758 Quick Installation Manual
MuxLab 500757 Quick Installation Manual
MuxLab 500754 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
MuxLab 500758 Quick Installation Manual
MuxLab 500752 Quick Installation Manual
manualsdatabase
Your AI-powered manual search engine