NAPCO Gemini GEM-X255 Installation Instructions Manual

Also see for Gemini GEM-RP1CAe2: Installation instructions Installation instructions Installation instructions Installation instructions Operating guide

NAPCO Gemini GEM-X255 Installation Instructions Manual Manual pdf 24 page image

X GEM-X255 Installation Instructions L NAPCO Security SystemsWI1093C 3/04! Page 24Arming in STAY MODESTAY MODE provides partial protection by allowing free movement within the premises, while still protecting the perimeterzones. Exit/Entry doors are provided with Exit/Entry delays. A "Classic" series keypad will display "SYSTEM ARMED" with a BypassIcon and a RED LED that remains ON, while a GREEN LED blinks. With "K Series" keypads such as the GEM-K1CA, pressingP bypasses all interior zones simultaneously, and arms the panel in "STAY MODE". The keypad will display "ARMED STAY".If P is pressed when the panel is already armed in STAY MODE, the panel will enter "Instant Mode" and eliminate the entrytime delay period.Instant ArmingINSTANT ARMING allows exit/entry zones to immediately go into alarm when violated, with no Exit/Entry time delay. Thisfeature can be used to provide instant protection while you or someone else is on the premises. With the "Classic" keypads, toarm "Stay" and obtain Instant Arming, press E and F, then enter your user code and press D. With the "K Series"keypads, enter your user code and press P. Then press and hold P until keypad beeps Instant Arming will be auto-matically reset on disarming.Auto Arming (Not for UL Installations)AUTO ARM allows the User to automatically arm the system at a specified time of the day and on specific days of the week.Schedule a specific closing time on any/all day(s) of the week. After a specific Fail-to-Close Window Start Time, if the user hasnot Armed the system during the Window Length, and the system has been instructed to "Fail-to-Close' and 'Auto Arm if notclosed at end of Window" then the system will arm, providing a 15 minute warning. CAUTION: If Automatic Interior Bypass/Easy Exit is selected, panel will Auto Arm in STAY Mode.Delaying an Auto Arm (Not for UL Installations)During the 15 minute pulsating sounder warning of an Auto Arm, a User can press the R or A button, until "TO DE-LAY AUTO ARM / PRESS 1-4 / N" is displayed. Enter the number of hours to delay arming, followed by the U or D button. If"DELAY AUTO ARM Y/N" is displayed, press the "NEXT/YES" button. The sounder can be silenced by pressing the C buttonduring the 15 minute interval, but will come back on in the last 1 minute. This feature may be canceled by arming and disarmingthe keypad.EZ Arm (Easy Arm)EASY ARM provides one button arming for non-security critical premises. Select Easy Arming for each Keypad, with op-tional reporting of Easy Arm Closings as User 199. Disarming still requires a valid user code.!To arm, press the D button for "Classic" keypads;!To arm, press and hold P or Q for 3 seconds for "K Series" keypads.Keyswitch ArmingKEYSWITCH ARMING allows a zone input to be used to arm/disarm. The area will arm/disarm when the zone is momen-tarily shorted through a Momentary Switch. An end-of-line resistor must be used. Select Keyswitch Arm to optionally report asUser 200.Remote Arming (Not for UL Installations)REMOTE ARMING allows computer software control of arming/disarming of the system for non-security critical installations.Select Remote Arm to optionally report as User 34.Priority ArmingA 2-second tone and "CAN'T ARM SYSTEM/ZONE FAULTED" displayed when attempting to arm indicates a priority condition; that is, aproblem exists on at least one zone that has been designated as a Priority Zone, or a system trouble exists. The trouble(s) mustbe corrected before the panel can be armed. The display will read "ZONE FAULTED", then automatically scroll through all unsecuredzones. If a system trouble is indicated, it will display the system trouble.Area Arming/Manager's ModeIn a partitioned system, any of eight secured areas may be armed (or disarmed) from the Manager's Mode (if enabled). TheManager's Mode, is a low-security mode of operation. It provides quick access to other areas without having to go to anotherkeypad of another area.!To arm or disarm the alternate area (for "Classic" keypads):1. Press a button between 1 and 8 representing the alternate area.BASIC OPERATION