NEC M403W User Manual

Also see for M283X: Installation guide Quick setup guide Quick setup guide

Contents

NEC M403W User Manual Manual pdf 148 page image

1378. AppendixCommon Problems & Solutions(→ “Power/Status/Lamp Indicator” on page 136.)Problem Check These ItemsDoes not turn onor shut down• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote controlis on� (→ pages 14, 15)• Ensure that the lamp cover is installed correctly. (→ page 135)• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the roomwhere you are presenting is particularly warm, move the projector to a cooler location�• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of itslife� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� (→ page 116)• The lamp may fail to light. Wait a full minute and then turn on the power again.• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1700 metersor higher� Using the projector at altitudes approximately 5500 feet/1700 meters or higher without setting to [HIGHALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a coupleminutes and turn on the projector� (→ page 102)If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image forsome time and then the projector will display the image� Wait for a moment�Will turn off • Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. (→ page 97, 105)No picture • Use the input select button on the remote control to select your source (COMPUTER, HDMI1, HDMI2, VIDEO,USB-A, LAN, or USB-B)� (→ page 17) If there is still no picture, press the button again�• Ensure your cables are connected properly.• Use menus to adjust the brightness and contrast. (→ page 89)• Ensure that the lens cover is open. (or lens cap is removed on M353WS/M303WS/M333XS) (→ page 5, 15)• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (→ page 116)• Enter your registered keyword if the Security function is enabled. (→ page 33)• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning onthe power to the notebook PC�In most cases the output signal from the notebook PC is not turned on unless connected to the projector beforebeing powered up�* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saveror power management software�• See also the next page�Picture suddenly be-comes dark• Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]� (→ page 102)Color tone or hue is un-usual• Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (→ page 96)• Adjust [HUE] in [PICTURE]. (→ page 89)Image isn’t square to thescreen• Reposition the projector to improve its angle to the screen. (→ page 18)• Use the Keystone correction function to correct the trapezoid distortion. (→ page 22)Picture is blurred • Adjust the focus. (→ page 21)• Reposition the projector to improve its angle to the screen. (→ page 18)• Ensure that the distance between the projector and screen is within the adjustment range of the lens.(→ page 117)• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.Should this happen, let the projector stand until there is no condensation on the lens�F l i c k e r a p p e a r s o nscreen• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1700meters or lower� Using the projector at altitudes less than approximately 5500 feet/1700 meters and setting to [HIGH ALTI-TUDE] can cause the lamp to overcool, causing the image to flicker� Switch [FAN MODE] to [AUTO]� (→ page 102)Image is scrolling ver-tically, horizontally orboth• Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supportedby the projector� (→ page 149)• Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 91)Remote control doesnot work• Install new batteries.(→ page 11)• Make sure there are no obstacles between you and the projector.• Stand within 22 feet (7 m) of the projector. (→ page 11)Indicator is lit or blink-ing• See the POWER/STATUS/LAMP Indicator. (→ page 136)Cross color in RGBmode• Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 26)• Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→ page 90)For more information contact your dealer.