NEC MultiSync P403 User Manual

Also see for P703: Specification Manual Specification Specifications Installation guide

Contents

NEC MultiSync P403 User Manual Manual pdf 28 page image

English-26ADVANCED OPTION1INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices areconnected.NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.NONENONE The Monitor will not search the other video input ports.FIRST DETECT* 2 When the current video input signal is not present, then the monitor searches for a video signalfrom the other video input port. If the video signal is present in the other port, then the monitorswitches the video source input port to the new found video source automatically.The monitor will not look for other video signals while the current video source is present.LAST DETECT*2 When the monitor is displaying a signal from the current source and a new secondary sourceis supplied to the monitor, the monitor will automatically switch to the new video source. Whencurrent video input signal is not present, the monitor searches for a video signal from the othervideo input port. If the video signal is present in the other port, then the monitor switches thevideo source input port to the new found video source automatically.VIDEO DETECT Y/Pb/Pr, Y/Pb/Pr2* 1, SCART* 1, VIDEO*1 or S-VIDEO*1 inputs will have priority over DVI, VGA,RGB/HV* 1. When Y/Pb/Pr, Y/Pb/Pr2*1, SCART* 1, VIDEO*1 or S-VIDEO*1 input signal is presentthe monitor will change and keep to the Y/Pb/Pr, Y/Pb/Pr2* 1 , SCART*1 , VIDEO*1 or S-VIDEO*1input.CUSTOM DETECT Set the priority of input signals.When CUSTOM DETECT is selected, monitor searches listed inputs only.LONG CABLE COMP*1(Analog input only)Manually compensates for image degradation caused from using a long cable.ON/OFF ON: Activates this function.OFF: Deactivates this function.OFFSOG PEAK Adjusts the sensitivity of the Sync On Green input signals. Adjusts the slice level when separatingsynchronization from sync On Green signal input. Press “LEFT” or “RIGHT” to select.0GAIN Adjusts gain value. 0R-H.POSITION Adjusts the position of the red component of the image. 0G-H.POSITION Adjusts the position of the green component of the image. 0B-H.POSITION Adjusts the position of the blue component of the image. 0SYNC TERMINATION Selects the terminate resistance for matching the cable impedance. HIGHINPUT CHANGE Sets input change speed. When selected “SUPER”, allows to switch high-speed between set twosignals.NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.“SUPER” is released when selecting IMAGE FLIP except for NONE.This function should be chosen after all adjustment options have been made for the input.NORMALTERMINAL SETTINGDVI MODE Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” whenPC or other computer equipment is connected. Select “DVI-HD” when DVD player, which hasDVI-D output, is connected.DVI-PCD-SUB MODE Selects the type of signal associated with the D-SUB input.RGB: Analog input (R, G, B, H, V)COMPONENT: Component (Y, Cb/Pb, Cr/Pr)RGBBNC MODE*1 Selects the kind of equipment which is connected to the BNC input.RGB: Analog input.COMPONENT: Component.RGBSCART MODE* 1 Input mode for devices using SCART connectors. OFFDisplayPort Selects DisplayPort mode [1.1a] or [1.2].[1.2] should be selected when using Multi-Stream Transport.* 31.1aHDMI SIGNAL RAW: Disable the expanded feature.EXPAND: Expand image contrast and increase detail in the dark and bright areas.EXPAND*1: This function depends on which option board you use.*2: Only for DVI, DPORT, VGA, RGB/HV* 1, HDMI, HDMI2*1, DPORT2* 1, DPORT3* 1 input.*3: Multi-Stream Transport requires the corresponding video card.