Napoleon Ascent X 70 Series Installation And Operation Manual

Also see for Ascent X 70 Series: Installation manual

Contents

Napoleon Ascent X 70 Series Installation And Operation Manual Manual pdf 30 page image

W415-1793 / A / 05.07.18EN30operation8.9 eFIRE Controller application8.10 low battery(4) AA Batteries(4) AA BatteriesRESET/PROGRAM BUTTON (PRG)A. The battery holder is located in the valve compartment,accessible for programming the remote.B. Install 4 AA batteries, Ensure that the positive and negativeends correspond with those identified in the battery holder.C. In the case of a power outage, the 3 position slider switchneeds to be in the “ON” position (left).note:Ensure the 3 positions slider switch is in the “REMOTE”position (middle).Napoleon’s eFIRE application will revolutionize the way you use your fireplace! We have cracked the code andpresent to you the first fireplace to be controlled by Bluetooth technology, using an intuitive app on your mobiledevice.When fully equipped (if applicable), the eFIRE application allows you to select from a multitude of colours to suityour mood or décor simply by scrolling through the colour wheel. Additionally, Napoleon’s eFIRE application allowsyou to control many other functions of your fireplace, including on/off, flame height, light feature, blower, and atimer to create a schedule for your fireplace that works for you.Using the instructions on the eFIRE Controller application website http://napoleonfireplace.com/efire, installthe application and enjoy the features the eFIRE Controller application has to offer. ** Visit the website or contact your authorized dealer for appliance-specific information and/or frequently askedquestions regarding features and products available with the eFIRE Controller application.note:The remote control is considered the master control for the appliance and can always be used to turn theappliance off (ex. the eFIRE Controller application user, in control of the appliance, leaves the home).8.11 battery holder / backup installation23.3Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76°FIPI 76°FCPI“beep” will confirm the reception of the command.Mode Key73 2376°F68Room TemperatureSet Temperature76°FMAX76°FOFF 76°F76°F76°FHiFlame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76°F76°F68 76°FHi76°FOFF 76°F76°FIPI 76°FCPIONSMART°F °CThe life span of the remote batteries depends on various factors: quality of the batteries,the number of ignitions, etc.When the transmitter batteries are low, a battery icon will appear on the LCD displaybefore all battery power is lost. When the batteries are replaced, this icon will disappear.When the receiver batteries are low, no “beep” will be emitted from the receiver whenit receives an on/off command. This in an alert for the receiver that there’s low battery.When the batteries are replaced the “beep” will be emitted from the receiver when the on/off key is pressed.If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding thethree position slider switch on the receiver to the on position. This will bypass the remote control feature and theappliance main burner will come on if the gas valve is in the on position.ADD TITLE: IN THE EVENT OF A POWER FAILUREIf the receiver is equipped with batteries they will enable flame height control or on/off function to control theappliance during a power failure. Blower and Night Light™ operation is not possible. Refer to “applianceoperation” section when communications between receiver and transmitter have been lost. The receiver willemit a “beep” sound to confirm programming has been successful once power is restored. During a powerfailure, if the appliance was on, the flame height will stay at the setting prior to the failure. If off when the failureoccurs and then turned on, the fl ame height will come on at “Hi”. The fl ame height can then be controlled by theremote.ADD TITLE: LOW BATTERY / MANUAL BYPASSADD TITLE: Night Light Dimmer Control76°F68Room TemperatureSet Temperature76°FMAX76°FOFF 76°F76°F76°FHiFlame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76°F68 76°FHi76°FOFF 76°F76°FIPI 76°FCPIONSMARTThe auxiliary function controls the Night Light™ with dimmable control.A. Use the mode key to guide you to the Night Light™ icon.B. The intensity of the output can be adjusted through 6 levels.Use the up/down arrow keys to adjust the output level. A single beepwill confi rm reception of the command.ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTIONA. When the transmitter is in the off position, use the mode key to guideyou to the CPI mode icon.B. Press the up/down to switch between IPI and CPI modes. A singlebeep will confirm reception of the command.Blue LCD DisplayOn / Off KeyUp / Down Arrow KeyMode KeyTemperature Key73 2376°F68Room TemperatureSet Temperature76°FMAX76°FOFF 76°F76°F76°FHiFlame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76°FOFF 76°FON76°F76°F68 76°FHi76°FOFF 76°F76°F76°FONSMART°F °CBlue LCD DisplayOn / Off KeyUp / Down Arrow KeyMode KeyTemperature Key73 2376°F68Room TemperatureSet Temperature76°FMAX76°FOFF 76°F76°F76°FHiFlame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76°FOFF 76°FON76°F76°F68 76°FHi76°FOFF 76°F76°FIPI 76°FCPIONSMART°F °CSet Temperature76°FMAX76°FOFF 76°F76°F76°FHiFlame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 676°Fchild lock76OFF 7676°FIPI 76°FCPISMARTIf the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPIto CPI position to enable remote CPI operation. If the switch is set to IPIthen it will only work in IPI regardless of what is set on the remote controlhandset.note: