Nilfisk-Advance RS 501 Instructions For Use Manual

Also see for RS 501: User manual Service manual User manual

Contents

Nilfisk-Advance RS 501 Instructions For Use Manual Manual pdf 35 page image

INSTRUCTIONS FOR USE ENGLISHRS 501 33015498(3)2008-02 19LIGHTING SYSTEM OPERATIONTo turn on the lighting and signalling system, use the combination switch (1, Fig. E), having the following functions:Headlights off, with mark (1b) at the symbol ORunning lights on, with mark (1b) at the symbolLow beam on, with mark (1b) at the symbolHigh beam on, with mark (1b) at the symbol and lowered lever (1a)High beam temporary on, lifting the lever (1a)Right turn signal on, bringing the lever (1a) forwardLeft turn signal on, bringing the lever (1a) backwardHorn activation, pushing the lever (1a) in the direction shown by the arrow (1c)HAZARD WARNING LIGHT OPERATIONTurn on the hazard warning lights with the switch (22, Fig. D).HOPPER MANUAL LIFTINGTo lift/lower the hopper (12, Fig. G) manually (when the diesel engine is faulty, etc.) perform the following procedure.Hopper manual liftingCheck that the machine is on a solid and level ground, especially if the hopper (12, Fig. G) is full.Turn off the engine, by turning the ignition key (17, Fig. D) counterclockwise, to the end of stroke, then remove it.Remove the ignition key (17, Fig. D).Engage the parking brake (7, Fig. E).Open the right panel door (16, Fig. G) by releasing the fasteners (17) with the supplied key.Remove the hand pump lever (29, Fig. F).Install the lever (1, Fig. L) on the hand pump (2).Turn the hopper lifting/lowering selector (3, Fig. L) to the lifting position (to lift the hopper turn the selector on the right, to lowerthe hopper turn the selector on the left) and, if necessary, try to pump with the lever (1).Carefully activate the pump (2, Fig. L) with the lever (1) and lift the hopper completely.Remove the lifted hopper locking pins (9, Fig. F) from the housings (10), and place them into the holes (11).Hopper manual loweringRemove the two locking pins (9, Fig. F) from the holes (11) and place them into the housings (10).Turn the selector (3, Fig. L) to the lowering position and activate the pump (2) with the lever (1) until the hopper is completelylowered.Turn the selector (3, Fig. L) to neutral position.Remove the lever (1, Fig. L) from the pump and place it in its housing (29, Fig. F).Close the right panel door (16, Fig. G) by engaging the fasteners (17) with the supplied key.LIFTED HOPPER LOCKING PIN INSTALLATIONBefore working under the lifted hopper (1, Fig. F), it is necessary to install the locking pins (9) according to the following procedure.WARNING!For safety purposes, before working under the lifted hopper, it is necessary to install the locking pins (9, Fig. F).This procedure is necessary even if the hopper lifting cylinders are equipped with parachute valves that preventthe hopper from lowering accidentally in case of break/leakage from a pipe/itting on the hydraulic system.Locking pin installationLift the hopper (12, Fig. G) completely according to the procedure shown in the relevant paragraph.Turn off the engine with the ignition key (17, Fig. D) and engage the parking brake with the lever (7, Fig. E).Remove the lifted hopper locking pins (9, Fig. F) from the housings (10), and place them into the holes (11).Locking pin removalIf necessary, start the machine and slightly lift the hopper to release the locking pins.Remove the two locking pins (9, Fig. F) from the holes (11) and place them into the housings (10).Lower the hopper (12, Fig. G) completely according to the procedure shown in the relevant paragraph.––––––––1.2.3.4.5.6.7.8.9.10.11.12.13.14.1.2.3.4.5.6.https://harrissupplyind.com - To Order Parts Call 608-268-8080