Norco 82300 Setup, Operating, Maintenance Instructions

Norco 82300 Setup, Operating, Maintenance Instructions Manual pdf 1 page image

MODELS 82300 & 82301 1 TON, 82303 1/2 TON, & 82315 3/4 TON WHEEL DOLLIESAND 82302 1/2 TON CAPACITY HIGH LIFT WHEEL DOLLYSETUP • OPERATING • MAINTENANCE INSTRUCTIONSPROFESSIONAL LIFTING EQUIPMENT®BEFORE USING THIS WHEEL DOLLY, READ THIS MANUALAND THE ADDITIONAL INSTRUCTION MANUAL ON THE WINCH(MODEL 82302 ONLY) COMPLETELY AND THOROUGHLY,UNDERSTAND THEIR OPERATING PROCEDURES, SAFETYWARNINGS AND MAINTENANCE REQUIREMENTS. FAILURETO DO SO COULD CAUSE ACCIDENTS RESULTING INSERIOUS OR FATAL PERSONAL INJURY AND/OR PROPERTYDAMAGE.The use of wheel dollies is subject to certain hazards that cannotbe prevented by mechanical means, but only by the exercise ofintelligence, care, and common sense. It is therefore essential tohave owners and personnel involved in the use and operation ofequipment who are careful, competent, trained, and qualified inthe safe operation of the equipment and its proper use. Examplesof hazards are dropping, tipping, or slipping of loads causedprimarily by improperly securing loads, overloading, off-centeredloads, use on other than a hard level surface, and using equipmentfor a purpose for which it was not designed.It is the responsibility of the owner to make sure all personnel readthese manuals prior to using this device. It is also the responsibilityof the device owner to keep these manuals intact and in a convenientlocation for all to see and read. If the manuals are lost or notlegible, contact Norco Industries, Inc. for free replacements. If theoperator is not fluent in English, the product and safety instructionsshall be read to and discussed with the operator in the operator’snative language by the purchaser/owner or his designee, makingsure that the operator comprehends its contents.WARRANTYThis product is covered by a Limited Lifetime Warranty. For detailssee the back cover of Norco’s product catalog.IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATINGWARNINGInspect the wheel dolly before each use. Do not use the wheel•dolly if it is damaged, altered, modified, in poor condition,leaking hydraulic fluid, or has loose or missing hardware orcomponents. Take corrective action before using the wheeldolly.Do not exceed rated capacity. Use only on a hard level surface.•Stay out from underneath a load that is being lifted or•suspended.Apply load as close to the vertical portion of the lifting member•as possible.Before moving the load, assure that the load is centered and•secured with the load restraint device provided.Before moving, lower the load to the lowest possible point.•No alterations or modifications shall be made to this product.•SETUPInsert the large diameter end of the jack handle into the pump1.handle receiver and secure the handle to the receiver with thewasher and bolt provided.The models 82300 and 82301 are equipped with adjustable2.lift arm rollers that should be adjusted in or out depending on thewheel diameter. The wheel dolly handles can be raised or loweredto your desired height and secured with the bolts provided.Sometimes air gets trapped in the hydraulic bottle jacks3.causing the jack ram to extend in sporadic increments instead ofone smooth extension.PURGING AIR FROM THE MANUAL PUMP SYSTEMOpen the release valve by turning the release valve knob ina.a counterclockwise direction two full turns.Pump the handle ten full strokes.b.Close the release valve by turning the release valve knob inc.a clockwise direction until tight.Pump the jack until the ram is extended to maximum height.d.If the condition remains, repeat steps “a” through “d” until airis purged from the system.Note: Revision letters (A, B, C, D etc.) after model numbers have been omitted as they do not affect the setup,operating and maintenance instructions of a particular jack unless otherwise noted.

/ 2

Related manuals for Norco 82300