Norco 86014 Quick Start Manual
MODELS 86014 4000 LBS. CAPACITY CROSS BEAM (PAIR)SETUP • OPERATING • MAINTENANCE INSTRUCTIONSPROFESSIONAL LIFTING EQUIPMENT®BEFORE USING THESE CROSS BEAMS, READ THISMANUAL COMPLETELY AND THOROUGHLY, UNDERSTANDITS OPERATING PROCEDURES, SAFETY WARNINGS ANDMAINTENANCE REQUIREMENTS. FAILURE TO DO SO COULDCAUSE ACCIDENTS RESULTING IN SERIOUS OR FATALPERSONAL INJURY AND/OR PROPERTY DAMAGE.The use of cross beams is subject to certain hazards that cannotbe prevented by mechanical means, but only by the exercise ofintelligence, care, and common sense. It is therefore essential tohave owners and personnel involved in the use and operation ofequipment who are careful, competent, trained, and qualified in thesafe operation of the equipment and its proper use. Examples ofhazards are dropping, tipping or slipping of loads caused primarilyby improperly securing loads, overloading and off-balanced loads,using equipment for a purpose for which it was not designed.Other hazards such as bending the beams can happen if warning,installation, setup, operating and maintenance instructions are notfollowed.It is the responsibility of the owner to make sure all personnel readthis manual prior to using these beams. It is also the responsibilityof the device owner to keep this manual intact and in a convenientlocation for all to see and read. If the manual is lost or not legible,contact Norco Industries, Inc. for a free replacement. If the operatoris not fluent in English, the product and safety instructions shall beread to and discussed with the operator in the operator’s nativelanguage by the purchaser/owner or his designee, making surethat the operator comprehends its contents.WARRANTYThis product is covered by a Limited Lifetime Warranty. For detailssee the back cover of Norco’s product catalog.IMPORTANT: READ THESE INSTRUCTIONS BEFORE INSTALLING & OPERATINGWARNINGUse these cross beams on the Norco Model 86006 Open•Center Pit Lift only.Use only for their intended purpose.•Vehicle lift contact points on the cross beams shall not exceed•four inches (4”) away from the lift pads under any circumstance.Use the vehicle manufacturer’s recommended lift points only.•Position the vehicle in relationship to the cross beams so the•vehicle’s weight is evenly distributed.Make sure setup is stable and secure before lifting.•Inspect the cross beams for mechanical fitness before using.•Do not use the cross beams if they are cracked, broken, bentor show signs of damage or excessive wear.Do not use the cross beams if the locating angles are not•properly installed and secured on the bottom of the beams.SETUPLocating angles must be installed on the bottom of both cross1.beams (see figure 1). Since the distance between lift pads varyaccording to the different pit widths, measure the distance betweenthe lift pads (see figure 2).Install the square mounting washers in between the ribs of the2.extruded cross beams as shown in figure 1.Place the locating angle where the leg of the angle with holes3.faces the bottom of the beam and the other leg of the angle facesinboard towards the center of the beam (see figure 1).Feed the hex head bolts and washers through the holes in4.the locating angles until the bolts make contact with the squaremounting washers.Turn the bolts in a clockwise direction until they thread into the5.holes in the square mounting washers. Do not tighten as you willhave to slide the angles into position.Using a square on the side of the cross beam, draw a line6.across the bottom of the cross bar ribs where the lift pad distanceis measured. The locating angles should be equal distances awayfrom the ends of the cross beams while maintaining the lift paddistance.Align the corners of the locating angles with the lines drawn7.on the cross beam ribs and tighten the bolts until the lockwasherscollapse flat. Do not over-tighten. Install the cross beams on thelift pads to make sure the locating angles clear the inside of the liftpads. If they do not line up, loosen the bolts and make the requiredadjustments.Note: Revision letters (A, B, C, D etc.) after model numbers have been omitted as they do not affect the setup,operating and maintenance instructions of a particular jack unless otherwise noted.SIDE OF CROSS BEAM3/8"-16 x 1"HEX HEAD BOLTLOCATINGANGLELOCATINGANGLE CORNERCROSSBEAM RIBSQUAREMOUNTINGWASHER3/8" SPLIT MEDIUMLOCKWASHERFigure 1 |
Related manuals for Norco 86014
Norco 82304 Setup, Operating, Maintenance Instructions
Norco 82300 Setup, Operating, Maintenance Instructions
Norco 82306 Setup, Operating, Maintenance Instructions
Norco 82990C Setup, Operating, Maintenance Instructions
Norco 72675 Setup, Operating, Maintenance Instructions
Norco 79324 Setup, Operating, Maintenance Instructions
Norco 72674 Setup, Operating, Maintenance Instructions
Norco 78500 Setup, Operating, Maintenance Instructions
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine