Repair 6-3Part 1612500−02 2018 Nordson CorporationPower Supply ReplacementNOTE: If replacing the powder path, skip this procedure.1. Slide the power supply (21) out of the gun body.2. Check the gasket (23) on the back of the bulkhead (24). Replace it if itis damaged. The gasket is secured to the bulkhead withpressure-sensitive adhesive.212024 20A23Figure 6-3 Removing the Power Supply from the Gun Body20. Gun body20A. Air wash tubing (filter assembly)21. Power supply23. Gasket24. Bulkhead3. Slide the new power supply into the upper cavity of the gun body,guiding the gun body ribs between the raised grooves on the top of thepower supply.4. Press on the end of the power supply to ensure that the power supplycontact tip is firmly seated against the brass contact inside the gun body.5. Route the power supply harness connector through the top hole in thebulkhead.6. If not replacing the powder path or cable, skip the next procedure andgo to page 6-5 to reassemble the gun.Powder Path ReplacementNOTE: Skip these steps if not replacing the powder path or cable. Go topage 6-5 to reassemble the spray gun.1. See Figure 6-4. Remove the outlet tube (22) from the inlet tube. Theelbow portion of the outlet tube is held onto the inlet tube with a tightO-ring fit; wiggle the elbow back and forth to pull it free.2. Remove the two M3 x 20 screws (31B) from the handle base (39).3. Pull the base away from the handle, swing the bottom of the ground pad(27) up and away from the handle, then remove it. Leave the groundwire connected to the ground pad.

Safety

Personal Safety

Grounding

System Setup

System Connections

System Setup and Connections

Spray Gun Connections

Air Tubing and Powder Hose

Pump and Hopper Connections

Connecting the Powder Hose to the Pump

Mobile Systems

System Electrical Connections

Entering Configuration Mode

Function Settings

Description

Mobile System Components

Equipment Labels

Operation

Displays and LEDs

Custom Electrostatic Mode

Classic AFC Mode

Powder Flow Settings

Smart Flow Mode Settings

Classic Flow Mode Settings

Spray Gun Operation

Purging

Maintenance

Cleaning Flat and Corner Spray Nozzles

Daily Maintenance

troubleshooting

General Troubleshooting Chart

Spray Gun Power Supply Resistance Test

Electrode Support Resistance Test

Gun Cable Continuity Test

Repair

Power Supply Replacement

Powder Path Installation

Gun Reassembly

Changing From Conical to Flat or Corner Spray Nozzle

Cable Replacement

Cable Installation

Switch Installation

Electrode Support Assembly Replacement − XD Version

Electrode Support Assembly Replacement − SD Version

Controller Repair

Rear Panel Components

System Part Numbers

Spray Gun

Electrode Support Assemblies

Spray Gun Options

Controller Parts

Front Panel and Internal Cabinet Ground Parts List

Rear Panel Parts Illustration

Rear Panel Parts List

Manifold Illustration and Parts List

System Components and Parts

System Options

Wiring Diagram

Nordson Encore Series Customer Product Manual

Specifications

Bundling Tubing and Cable

System Air Supply

Power Supply

Daily Operation

Cleaning Conical Nozzles and Deflectors

Shutdown

Troubleshooting

Trigger Switch Replacement

Parts

Rear Panel Parts

Manifold Parts

declaration of conformity

Encore LT

nordson corporation

Part

Controller Wall Mounting

Controller Connections

VBF System Setup

Feed Hopper and Wall/Rail Mount System Setup

Coupling Installation

Controller Configuration

Issued

Vibratory Box Feeder Operation

Changing Flat Spray Nozzles

Changing Conical Nozzles and Deflectors

Installing the Optional Pattern Adjuster Kit

Powder Path Replacement

Vibrator Motor Replacement

Spray Gun Parts Illustration

Spray Gun Parts List

Flat Spray Nozzles

Degree Corner-Spray Nozzle

Conical Nozzle, Deflectors and Electrode Assembly Parts

Pattern Adjuster Kit

Ion Collector Kit

Powder Hose and Air Tubing

Optional Transportable Manual System

Encore PE

Encore Series