Contents - December
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Standard 16.00 April
- References
- Content list
- Access through the system terminal
- Access through the maintenance telephone
- Circuit cards
- Data disks
- Options 51C, 61C,and 81C cable guidelines
- Reference list
- Pedestal grills
- A0321130 Fan Unit
- A0378252 Battery Pack Assembly
- NTAG26 Extended Multi-frequency receiver
- NT5K09 Quad Digitone Receiver
- NT5K10 Dual Loop Peripheral Buffer Card
- NT5K1106 Enhanced Peripheral Equipment Card Cage
- Sender/Receiver Card
- NT1P61 Fibre Superloop Network Card
- NT1P62 Fibre Peripheral Controller Card
- NT5D10 68060 Call Processor (CP) Card
- NT5D12AA Dual DTI/PRI (DDP)
- Installing the DDP card
- NT5D20 IOP/CMDU
- with the NT5D20 IOP/CMDU
- NT5D30AA Dual InterGroup Switch (DIGS) card
- NT6D3903 CPU/Network Module Card Cage
- NT6D40, NT6D41, NT6D42, Power Supply DC
- NT5D61 Input/Output Disk Unit with CD-ROM (IODU/C)
- Splitting the Cores
- Replacing the IODU/C in a redundant system
- Replacing the IODU/C in an Option 51C
- Completing the upgrade
- NT6D52 Rectifier –48 V/30 A
- Core/Network Card Cage
- NT6D6003 Core Bus Terminator Card
- NT6D63 I/O Processor Card
- NT6D64 Core Multi Drive Unit
- NT6D65 and NTRB34 Core to Network Interface Cards
- NT6D66 Call Processor Card
- NT7D10 Power Distribution Unit DC
- NT8D06, NT8D21, NT8D29 Power Supply AC
- NT7D15 System Monitor
- NT7D67CB Power Distribution Unit DC
- NT7R51 Local Carrier Interface Card
- NT7R52 Remote Carrier Interface Card
- NT8D01 Controller Card
- Intelligent Peripheral Equipment Card
- NT8D04 Superloop Network Card, QPC414 Network Card
- NT8D17 Conference/TDS Card
- NT8D18 Network/DTR Card
- NT8D19 Memory/Peripheral Signaling Card
- NT8D22 System Monitor
- NT8D41 Dual or Quad Port Serial Data Interface card
- NT8D46AC Thermostat Harness
- NT8D46AM, NT8D46DC Air Probe Harness
- NT8D52AB, NT8D52DD Pedestal Blower Unit
- NT8D53CA Power Distribution Unit AC
- NT8D53AD Power Distribution Unit
- Power Distribution Unit
- NT8D1103 CE/PE Module Card Cage
- NT8D1303 PE Module Card Cage
- NT8D3403 CPU Module Card Cage
- NT8D3503/NT8D3507 Network Module Card Cage
- NT8D3703 IPE Module Card Cage
- NT8D33 Small Systems Multi Disk Unit
- systems equipped with NT5D61 IODU/C cards
- NT9D19 68040 Call Processor (CP) card
- NT9D34 Enhanced Mass Storage Interface Card
- NTBK51AA Downloadable D-Channel Daughterboard
- NTND01 Integrated CPU/Memory Card
- NTND02 Misc/SDI/Peripheral Signaling Card
- NTND08, QPC939 ROM Card
- NTND09, QPC583 Memory Card
- NTND10, QPC581 Changeover and Memory Arbitrator Card
- NTND15, NT8D68 Floppy Disk Unit
- NTND16, NT8D69 Multi Disk Unit
- NTND31 ROM Card
- NTRB33 Fiber Junctor Interface card
- P0699798 Air Filter
- QMM42 Security Data Cartridge
- QPC43 Peripheral Signaling Card
- QPC215 Segmented Bus Extender Card
- QPC412 InterGroup Switch Card
- QPC441 Three-Port Extender Card
- QPC471, QPC775 Clock Controller Card
- QPC477 Bus Terminating Unit
- QPC841 Serial Data Interface Card
- QPC579 CPU Function Card
- QPC580 CPU Interface Card
- QPC584 Mass Storage Interface Card
- QPC659 Dual Loop Peripheral Buffer Card
- QPC687 CPU Card
- Replacing the QPC723A Circuit Card
- QPC742 Floppy Disk Interface Card
- QPC940 ROM Card
- Replacing the Security Device on the NT5D61 IODU/C
- Replacing the Security Device on a redundant system
- Replacing the Security Device on an Option 51C system
| 
Page 78 of 362 Replacing equipment553-3001-520 Standard 16.00 April 2000Note: Refer to “Software installation tool reference” in SoftwareConversion Procedures (553-2001-320).a Activate the software installation tool by inserting disk A1 from thesoftware package into the IOP/CMDU in the Core containing thereplacement IOP/CMDU.b Press the MAN RST button on the CP card in the Core containingthe replacement IOP/CMDU.c Select the following options in sequence:d Specify software installation from the hard disk and follow screendirections until the install menu returns.e Remove the disk from the IOP/CMDU.f Select the following options to quit and reboot the system:10 Test the replacement IOP/CMDU:If there is a problem, a CIOD system message is generated. to install software only to install ROM on the IOP part of theIOP/CMDU only to start installation to quit to confirm quit to reboot the systemThe system will load the software.Wait until the system sysloads and initializes.LD 137 to load the programDIS IOP to disable the IOP part of the IOP/CMDUTEST IOP to test the operation of the IOP part of theIOP/CMDUENL IOP to enable the IOP part of the IOP/CMDUTEST CMDU n to test the operation of the CMDU part of theIOP/CMDU where n is the inactive CoreIOP/CMDU |
