OHAUS SCOUT Service Manual

Also see for SCOUT: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

OHAUS SCOUT Service Manual Manual pdf 14 page image

2-4CHAPTER 2 THEORY OF OPERATION2.3.3 Low Voltage DetectorThe purpose of the Low Voltage Detector circuitry is to inform an operator when thebattery voltage drops to level which would cause improper operation of the balance andrequire replacement of the battery. Transistors Q4 and Q7 form the low voltagedetector. Transistor Q3 is turned on as long as the voltage across VR1 pins 1 and 3 ishigher than the emitter base voltage (0.6 V) of Q4. With a low voltage, Q4 turns off, sodoes Q7. The result is that the VLOW signal at pin 3 of Q7 goes high placing a high stateat pin 7 of microprocessor U1. The microprocessor U1 then sends a correspondingsignal to driver U7 which is the word equivalent of BAT. This data is then sent to thedisplay DS1 where the word BAT is displayed.2.3.4 Temperature A/D ConverterThe primary function of the Temperature A/D Converter is to compensate for tempera-ture changes of the Transducer during operation. It does this by converting the varyingdc analog voltages developed by the temperature sensor to a digital signal which isdirectly proportional to the analog voltages and represents temperature. The tempera-ture sensor is physically located on the Transducer. A current signal developed by thetemperature sensor is referenced to ground and is applied to the junction of resistors R9and R10 to the input pin 2 of U5A which is an integrator. A reference voltage is developedby resistors R4 and R5 (from the 5 volt source to ground) to pin 5 of U3B which is acomparator and pin 3 of U5A which is an integrator. The current through thetemperature sensor is measured by the duty cycle of resistor R11 which is switched from+5 volts dc and ground by U4A and U4F which act as electronic switches. The duty cycledetermines how much current is pulled out in this mode and how much is fed in. A signalfrom the microprocessor U1 pin 17 provides a duty cycle ranging from 10 to 30% to pin1 of U4A. U5A is an integrator which develops a sawtooth signal output which iscompared with the 1 volt reference signal by U3B comparator. When the sawtoothsignal from U5A at pin 1 is on the down slope and crosses the 1 volt reference point,comparator U3B outputs a low signal to the microprocessor pin 27 through resistor R43.The microprocessor interprets this signal as a value of current which is representativeof the temperature of the temperature sensor on the Transducer. The microprocessorthen sends a signal on pin 17 to pin 4 of U4A and pin 13 of U4F which are the electronicswitches. This square wave signal reverses the switching action and starts a newintegration of U5A.2.3.5 Full Bridge Weight A/D ConverterThe primary function of the Full Bridge Weight A/D Convertor is to convert the varyingdc analog voltages developed by a full bridge type Transducer to a digital signal whichis directly proportional to the analog voltages. This signal is then processed bymicroprocessor U1. The circuitry consists of integrator U5B, comparator U3A, elec-tronic switches U4A, U4B, U4C, and U4D with resistors R1, R2, R3, R7, R14, R34, R35,capacitors C1, C3, C12, C19 and transistor Q2. The circuitry functions in a similiarmanner as the Temperature A/D Converter except a duty cycle of 10 to 90% is achieved.The output of a full wave bridge Transducer is through resistor R13 to pin 6 of U5B. Theoutput of U5B is a sawtooth signal which is connected to U3A, pin 2.