Contents - maintenance manual
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- CONFIGURATION
- Printer Configuration
- Optional Configuration
- Specification
- Safety Standards
- OPERATION DESCRIPTION
- Main Control Board (BOARD-FFH)
- Power Supply Unit
- Electro-photographic Process
- Process operation descriptions
- Revision of LED Head Illumination
- Paper Jam Detection
- Cover Open
- Toner Low Detection
- Stacker-full Detection
- PARTS REPLACEMENT
- Parts Layout
- How to Change Parts
- Face -up Stacker Assy
- Contact Assy
- DC Fan Motor
- OP Panel Assy
- Board-FFH
- Stacker Assy, Damper Arm, Cover Rear
- Sensor Stacker Full
- Cable cover (guide film)
- Damper
- Feeder Unit-Front
- Roller Assy-Regist
- Motor -Main
- Guide Assy-Eject
- Heat Assy
- Roller feed (C)
- Roller Assy-BK
- Roller Assy-Feed
- LED Head
- Paper cassette, ROLLER Ass-Feed, ROLLER-Assy-Hoppibg
- Frame Assy-Separation
- Transfer Roller/TR Gear/TR Bearing
- EP lock shaft
- LEVER Assy- Out Sensor
- Toner sensor lever
- Paper sensor lever
- Inlet sensor lever
- Lever-Paper end & Lever-Paper near end
- Guide Assy-Cassette (L)
- Guide Assy-Cassette (R)
- ADJUSTMENT
- User maintenance mode
- user maintenance mode menu system
- System maintenance mode
- Engine maintenance mode
- engine maintenance mode menu system
- EEPROM initialization
- Adjustment When Replacing A Part
- Resetting the fuser counter
- Destination setting
- Setting of LED head drive time
- PERIODIC MAINTENANCE
- Cleaning the Plastic Film
- TROUBLESHOOTING PROCEDURES
- Preparation for Troubleshooting
- LCD message troubleshooting
- Image troubleshooting
- cyclic error
- poor fusing
- snowy print of high density pattern
- Program/Font ROM Location
- PARTS LIST
- Appendix A CENTRONICS PARALLEL INTERFACE
- OUTLINE
- MECHANISM DESCRIPTION
- JAM Release Mechanism
- Removing/Installing Duplex Unit
- Precautions Concerning Parts Replacement
- Parts Replacement Methods
- Board-LEX
- Connector (IMSA-9714N-14A)
- Photo Sensor
- SOLENOID Assy
- Motor
- TROUBLESHOOTING
- Troubleshooting Method
- Troubleshooting Flow
- PCB Layout
- Functions
- Description of operartion
- Hopper Mechanism
- Roller assy hopping, Roller assy feed
- Cover front assy
- Board-BBB
- Lever paper end, Lever paper near end
- Connector (IMSA-9714N-14B), Connector (IMSA-9714N-14A)
- Frange pulley, pulley Idle, Mini pitch belt, Plate Earth shaft Gear double, Tray switch assy
- Roller feed
- Bracket sub roller
- Frame side (L) assy
- Frame side (R) assy
- Precautions Prior to the Troubleshooting
- LCD Status Message List
- CONNECTION DIAGRAM
- External View and Component Names
- General Mechanism
- Separator
- AOLE-PCB
- Square-shaped connector
- Hopping Motor
- Planet gear
- Roller B
- Roller A
- Mini pitch belt & Feed roller
- Preparations for the Troubleshooting
- Interconnection Diagram
|
40931201TH Rev. 4 3 /CONTENTS1. CONFIGURATION ....................................................................................... 71.1 System Configuration ................................................................................................. 71.2 Printer Configuration .................................................................................................. 81.3 Optional Configuration ............................................................................................... 91.4 Specification ............................................................................................................... 111.5 Safety Standards ....................................................................................................... 131.5.1 Certification label .......................................................................................... 131.5.2 Warning label................................................................................................ 132. OPERATION DESCRIPTION ...................................................................... 142.1 Main Control Board (BOARD-FFH) ............................................................................ 162.2 Power Supply Unit ..................................................................................................... 202.3 Electro-photographic Process .................................................................................... 222.3.1 Electro-photographic process mechanism ................................................... 222.3.2 Electro-photographic process ....................................................................... 242.3.3 Process operation descriptions .................................................................... 282.3.4 Revision of LED Head Illumination ............................................................... 382.4 Paper Jam Detection ................................................................................................. 462.5 Cover Open ................................................................................................................ 472.6 Toner Low Detection .................................................................................................. 482.7 Stacker-full Detection ................................................................................................. 502.8 Page Size Detection .................................................................................................. 503. PARTS REPLACEMENT ............................................................................. 513.1 Precautions for Parts Replacement ........................................................................... 513.2 Parts Layout ............................................................................................................... 533.3 How to Change Parts ................................................................................................. 563.3.1 Face -up Stacker Assy ................................................................................. 573.3.2 Contact Assy ................................................................................................ 583.3.3 DC Fan Motor ............................................................................................... 593.3.4 OP Panel Assy ............................................................................................. 603.3.5 Board-FFH .................................................................................................... 613.3.6 Stacker Assy, Damper Arm, Cover Rear ..................................................... 623.3.7 Sensor Stacker Full ...................................................................................... 633.3.8 Cable cover (guide film) ................................................................................ 643.3.9 Damper ......................................................................................................... 653.3.10 Feeder Unit-Front ......................................................................................... 663.3.11 Roller Assy-Regist ....................................................................................... 673.3.12 Motor -Main .................................................................................................. 683.3.13 Guide Assy-Eject .......................................................................................... 703.3.14 Heat Assy ..................................................................................................... 713.3.15 Roller feed (C) ............................................................................................. 723.3.16 Roller Assy-BK ............................................................................................. 733.3.17 Roller Assy-Feed .......................................................................................... 743.3.18 LED Head ..................................................................................................... 753.3.19 Paper cassette, ROLLER Ass-Feed, ROLLER-Assy-Hoppibg ..................... 763.3.20 Frame Assy-Separation ................................................................................ 773.3.21 Transfer Roller/TR Gear/TR Bearing ............................................................ 783.3.22 EP lock shaft ................................................................................................. 793.3.23 LEVER Assy- Out Sensor............................................................................. 803.3.24 Toner sensor lever ........................................................................................ 813.3.25 Paper sensor lever ....................................................................................... 823.3.26 Inlet sensor lever .......................................................................................... 833.3.27 Power supply unit ......................................................................................... 84
PreviousNext |