Contents - maintenance manual
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- System Configuration
- Printer Configuration
- Optional Configuration
- Specification
- Safety Standards
- Electro-photographic process
- Main Control Board (BOARD-FFF)
- Power Supply Unit
- Process operation descriptions
- Revision of LED Head Illumination
- Paper Jam Detection
- Cover Open
- Toner Low Detection
- toner full state
- Stacker-full Detection
- Precautions for Parts Replacement
- Parts Layout
- How to Change Parts
- Face -up Stacker Assy
- Contact Assy
- DC Fan Motor
- OP Panel Assy
- Board-FFF
- Stacker Assy, Damper Arm, Cover Rear
- Sensor Stacker Full
- Cable cover (guide film)
- Damper
- Feeder Unit-Front
- Roller Assy-Regist
- Motor -Main
- Guide Assy-Eject
- Heat Assy
- Roller feed (C)
- Roller Assy-BK
- Roller Assy-Feed
- LED Head
- Paper cassette, ROLLER Ass-Feed, ROLLER-Assy-Hoppibg
- Frame Assy-Separation
- Transfer Roller/TR Gear/TR Bearing
- EP lock shaft
- LEVER Assy- Out Sensor
- Toner sensor lever
- Paper sensor lever
- Inlet sensor lever
- PERIODIC MAINTENANCE
- Cleaning the Plastic Film
- TROUBLESHOOTING PROCEDURES
- Preparation for Troubleshooting
- LCD message troubleshooting
- the printer does not work normally after being turned on
- jam error
- paper input jam (front feeder)
- paper feed jam
- paper exit jam
- duplex input jam
- paper size error
- data cannot be received through the oki hsp interface
- Image troubleshooting
- cyclic error
- print voids
- poor fusing
- snowy print of high density pattern
- WIRING DIAGRAM
- PCB Layout
- Program/Font ROM Location
- PARTS LIST
- appendix a centronics parallel interface
- OUTLINE
- Description of operartion
- Hopper Mechanism
- PARTS REPLACEMENT
- Parts Replacement Methods
- Roller assy hopping, Roller assy feed
- Cover front assy
- Board-BBB
- Lever paper end, Lever paper near end
- Motor
- Connector (IMSA-9714N-14B), Connector (IMSA-9714N-14A)
- Frange pulley, pulley Idle, Mini pitch belt, Plate Earth shaft Gear double, Tray switch assy
- Roller feed
- Bracket sub roller
- Frame side (L) assy
- Frame side (R) assy
- TROUBLESHOOTING
- Troubleshooting Method
- Troubleshooting Flow
- CONNECTION DIAGRAM
- Connector (IMSA-9714N-14A)
- Functions
- MECHANISM DESCRIPTION
- Precautions Concerning Parts Replacement
- Separator
- AOLE-PCB
- Square-shaped connector
- Hopping Motor
- Planet gear
- Roller B
- Roller A
- Mini pitch belt & Feed roller
- Precautions Prior to the Troubleshooting
- LCD Status Message List
- Interconnection Diagram
|
40930701TH DRAFT Vesion 3 /CONTENTS1. CONFIGURATION ....................................................................................... 71.1 System Configuration ................................................................................................. 71.2 Printer Configuration .................................................................................................. 81.3 Optional Configuration ............................................................................................... 91.4 Specification ............................................................................................................... 111.5 Safety Standards ....................................................................................................... 131.5.1 Certification label .......................................................................................... 131.5.2 Warning label ................................................................................................ 132. OPERATION DESCRIPTION ...................................................................... 142.1 Main Control Board (BOARD-FFF) ............................................................................ 162.2 Power Supply Unit ..................................................................................................... 202.3 Electro-photographic Process .................................................................................... 222.3.1 Electro-photographic process mechanism ................................................... 222.3.2 Electro-photographic process ....................................................................... 242.4.3 Process operation descriptions .................................................................... 282.3.4 Revision of LED Head Illumination ............................................................... 392.4 Paper Jam Detection ................................................................................................. 472.5 Cover Open ................................................................................................................ 482.6 Toner Low Detection .................................................................................................. 492.7 Stacker-full Detection ................................................................................................. 512.8 Page Size Detection .................................................................................................. 513. PARTS REPLACEMENT ............................................................................. 523.1 Precautions for Parts Replacement ........................................................................... 523.2 Parts Layout ............................................................................................................... 543.3 How to Change Parts ................................................................................................. 583.3.1 Face -up Stacker Assy ................................................................................. 593.3.2 Contact Assy ................................................................................................ 603.3.3 DC Fan Motor ............................................................................................... 613.3.4 OP Panel Assy ............................................................................................. 623.3.5 Board-FFF .................................................................................................... 633.3.6 Stacker Assy, Damper Arm, Cover Rear ..................................................... 643.3.7 Sensor Stacker Full ...................................................................................... 653.3.8 Cable cover (guide film)................................................................................ 663.3.9 Damper ......................................................................................................... 673.3.10 Feeder Unit-Front ......................................................................................... 683.3.11 Roller Assy-Regist ........................................................................................ 693.3.12 Motor -Main .................................................................................................. 703.3.13 Guide Assy-Eject .......................................................................................... 723.3.14 Heat Assy ..................................................................................................... 733.3.15 Roller feed (C) ............................................................................................. 743.3.16 Roller Assy-BK ............................................................................................. 753.3.17 Roller Assy-Feed .......................................................................................... 763.3.18 LED Head ..................................................................................................... 773.3.19 Paper cassette, ROLLER Ass-Feed, ROLLER-Assy-Hoppibg ..................... 783.3.20 Frame Assy-Separation ................................................................................ 793.3.21 Transfer Roller/TR Gear/TR Bearing ............................................................ 803.3.22 EP lock shaft ................................................................................................. 813.3.23 LEVER Assy- Out Sensor ............................................................................. 823.3.24 Toner sensor lever........................................................................................ 833.3.25 Paper sensor lever ....................................................................................... 843.3.26 Inlet sensor lever .......................................................................................... 85
PreviousNext |