Panasonic AW-UE150WP Operating Instructions Manual

Also see for AW-UE150KE: Operating instructions Operating instructions Operating instructions Operating instructions

Contents

Installation Instructions Before installation, always disconnect the DCconnectorWhen installing, always use the supplied components.Do not disassemble or modify the wall mount adaptor. Tightening up the mounting screws• Tighten up the screws and bolts securely to the degree that isappropriate for each of the materials used in the mounting locationand structures.• After tightening up the screws and bolts, check that there is nounsteadiness and that the parts have been tightened securely.• Use the specified tools and tighten the screws firmly.• Tighten up the screws using the specified torque driver. Do notuse electrical drivers or impact drivers. When the unit is no longer going to be used, donot leave it lying around, but be absolutely sureto dispose of it properly.For details on how to remove the unit, refer to “Removing thecamera” (→ page 14). When installing, transferring or disposing ofthe unit, be absolutely sure to hold it by itspedestal area.Problems may result if the camera head is held or rotated. Do not attach a filter, hood, extender or otherparts to the unit. Install the external DC power supply near themain power outlet, and position it in such away that its power plug can be plugged intoand unplugged from the outlet easily.When connecting the external DC power supply to a power outlet onthe ceiling or on any other surface where dust may collect, wipe offthe dust on the power plug at periodic intervals as an anti-trackingmeasure. Power switchThis unit does not have a power switch. When the poweris supplied, the pan, tilt, zoom and focusing operations areperformed.*1 Before proceeding with maintenance, be absolutelysure to disconnect the power plug from the power outlet.*1 • Under factory default conditions, the unit will be in Standbymode when power is supplied for the first time. (Status displaylamp: Lit orange)• When the power supply is cut off while the unit is in Standbymode, the unit will be in Standby mode the next time power issupplied. (Status display lamp: Lit orange)• When the power supply is cut off while the unit is in Power ONmode, the unit will be in Power ON mode the next time poweris supplied. (Status display lamp: Lit green)(For details, refer to “How to turn the power on and off”(→ page 59).) GroundingBefore operating the unit, check that SIGNAL GND has beensecurely grounded. If there is a possibility of noise interferenceEither wire the cables so that the power cable (ceiling light cord) ofAC 100 V*2 (AC 220 V*3 ) or more, and the signal cable are placedat least 1 meter (3.3 ft) apart.Alternatively run each cable through its own metal conduit.(The metal conduits must be grounded.)*2 For AW-UE150WP, AW-UE150KP*3 For AW-UE150WE, AW-UE150KE Radio signal interferenceIf the unit is positioned near a TV or radio transmitting antenna or astrong electrical field or magnetic field (such as that generated by amotor, transformer or power lines), its images may be distorted and/or the images may be affected by noise. When connecting the cables, ensure that theconnector areas will not be subject to any load.Doing so may cause malfunctioning. Allowing the generated heat to escapeThis unit allows the heat generated inside to escape from itssurfaces.Do not install the unit in a location where it will be surrounded bywalls or other surfaces and where heat will be trapped.In addition, the heat is dissipated to the bottom panel which willwarm up over time: This is normal and not indicative of any trouble. PoE++ power suppliesUse a PoE++ [IEEE802.3bt Draft ver.2.0 standard (LLDP notsupported)] compatible hub or power supply device. Network settingsThe network function of this unit does not work unless an initialaccount is set up (except when using the Easy IP Setup Software(→ page 57)). A personal computer is required to set up an initialaccount. (→ page 58)• Network connection with AW-RP150 also requires setup of aninitial account. When an initial account is not set up, AW-RP150can detect but cannot control this unit.7Installation precautions (continued)