7[VIDEO CONFIG]>COLOR TEMP D65SHARPNESS H 3SHARPNESS V 3I-P MODE MODE2MONO OFFSD ASPECT 4:3HD ZOOM NORMALVIDEO CONFIG menuVIDEO CONFIG SYSTEM CONFIGWith SYSTEM CONFIG selected, the following menu willappear.BACKLIGHTUsed to adjust the brightness of backlight.Set-value (underlined is default value)0 – 63 (BT-LH1800)0 – 32 – 63 (BT-LH1500)POSITIONUsed to set the display position of on screen menu.Set-value (underlined is default value)CENTER (center of screen), LT (top left of screen),RT (top right of screen), RB (bottom right of screen),LB (bottom left of screen).ERROR MESSAGEUsed to select whether or not displaying transmitting systemerror of SDI and HD-SDI. If an error is generated, “CRCCERROR” will be displayed.Set-value (underlined is default value)ON OFFSTATUS DISPLAYUsed to set the information display in case of input changeor the format display in case of signal input.Set-value (underlined is default value)CONTINUE 3SEC OFF OFFCONTROL LOCKAll menu items other than CONTROL LOCK and front panel operationsother than power switch are locked (invalidated). Even when locked, itreturns to preset value with picture adjusting knob pushed in.Set-value (underlined is default value)ON OFFSETUP• LOADUsed to read in the set-value being saved.“FACTORY” reads in the factory-adjusted value.Set-value (underlined is default value)FACTORY USER1*1) USER2* 1)USER3* 1) USER4* 1) USER5* 1)• SAVECurrent set-values can be saved up to 5.Set-value (underlined is default value)USER1 USER2 USER3USER4 USER5* 1) The contents of USER1 – USER5 and FACTORY are same atthe time of delivery from the factory.[SYSTEM CONFIG]>BACKLIGHT 63POSITION CENTERERROR MESSAGE ONSTATUS DISPLAY CONTINUECONTROL LOCK OFF[SET UP]LOAD FACTORYSAVE USER1SYSTEM CONFIG menuHow To Use On Screen MenuWith VIDEO CONFIG selected, the following menu will appear.COLOR TEMPUsed to set the color temperatureSet-value (underlined is default value)USER 0 – 63* 1) D93 D65SHARPNESS HUsed to set the sharpness in horizontal direction.Set-value (underlined is default value)0 –15*2) Default value3 (HD) 12 (SD) (BT-LH1800)2 (HD) 2 (SD) (BT-LH1500)SHARPNESS VUsed to set the sharpness setting in vertical direction.Set-value (underlined is default value)0 –15*2) Default value3 (HD) 3 (SD) (BT-LH1800)2 (HD) 2 (SD) (BT-LH1500)I-P MODEUsed to set the mode for IP change.Set-value (underlined is default value)MODE1 MODE2MONOUsed to make setting for mono-chrome display.Set-value (underlined is default value)ON OFFSD ASPECTUsed to set the aspect ratio in case of SD signal input.Select REMOTE when executing external change by REMOTE terminal.Set-value (underlined is default value)REMOTE 16:9 4:3HD ZOOMEnlarged 4:3 is displayed by PAN&SCAN in case of 1080I,1035I, 720P signal input.Select REMOTE when executing external change by REMOTEterminal.This item is displayed only when HD SDI input unit or compo-nent/RGB input unit is installed.Set-value (underlined is default value)4:3 NORMAL REMOTE* 1) By user setting, it is possible to change the color temperature in64 stages from 0 (around 3000K) to 63 (around 9300K).* 2) Sharpness value has a set-value and is displayed for each of in-put signal (HD/SD)