Panasonic CS-A12ATP5 Service Manual

Also see for CS-A12ATP5: Operating instructions

Panasonic CS-A12ATP5 Service Manual Manual pdf 22 page image

NAME OF EACH PART Remote Control Remote Control Signal.• Make sure it is not obstructed.• Maximum distance : 10 m.• Signal received sound.One short beep or one long beep. Notes for Remote Control.• Do not throw or drop.• Do not get it wet.• Certain type of fluorescent lamps may affectsignal reception. Consult your dealer. Do not place the remote control in a location exposedto direct sunlight, or next to a heating unit, or otherheat source. How to Insert the Batteries1 Gently press the place marked OPEN and slidethe cover towards you.2 Insert the batteries– Be sure the direction is correct. About the batteries• Can be used for approximately one year. Observe the following when replacing the batteries• Replace with new batteries of the same type.• Do not use rechargeable batteries (Ni-Cd).• Remove the batteries if the unit is not going to beused for a long period. Proper way to operate the remote control in thecase of ceiling/wall mounting.• Operate the remote control in parallel with the floor.(See the figure below)1 Signal Transmitter2 Operation Display3 Room Temperature Setting Button(self-illuminating button)4 Operation Mode Selection Button5 Sleep Mode Operation Button(self-illuminating button)6 Timer Setting Button7 Timer Selection Button8 OFF/ON Button(self-illuminating button)9 Fan Speed Selection Button0 Auto Airflow Direction Button! Timer Set/Cancel Button@ Manual Airflow Direction Selection Button# Reset Point(Press with fine-tipped object to clear the memory)1.5V1.5VOPEN12AUTOHEATCOOLDRYFANSPEEDCH HOFF ON OFF ONAUTOCOOLFANFANSPEEDDRYCH HOFF ON OFF ONCooling ModelHeat Pump Model"!#$357689421AUTOCOOLFANFANSPEEDOFF/ONTEMPMODE SLEEP FAN SPEEDAUTOMANUALTIMER AIR SWINGOFF/ON SET/CRESETDRYCH HOFF ON OFF ON• The signal changes as shown in the figure below.It means that the receiving conditions are bad andthe signal can not be controlled properly.O.K.OUT(Fig. 2)(Fig. 1) Horizontal LevelHOW TO OPERATE To start the operation• Press 1.• POWER indicator (green) on the indoor unit will lightup.• To stop, press once more. Setting Mode• Press 2 to select:-Cooling ModelAUTO – Automatic OperationCOOL – Cooling OperationDRY – Soft Dry OperationFAN – Air Circulation OperationHeat Pump ModelAUTO – Automatic OperationHEAT – Heating OperationCOOL – Cooling OperationDRY – Soft Dry OperationPREPARATION BEFORE OPERATION Indoor Unit1 Connect the power supply cord to an independentpower supply. Setting Temperature• Press 3 to increase or decrease the temperature.• The temperature can be set between:Cooling Model : 20°C ~ 30°CHeat Pump Model : 16°C ~ 30°C• Recommended temperature:• During AUTO Operation, press 3 to select:-• Operation with 2°C higher than the standardtemperature.• Operation with the standard temperature.• Operation with 2°C lower than the standardtemperature. Standard TemperatureCooling Model• Once the Automatic Operation is selected, the indoortemperature sensor operates automatically to selectthe desired operation mode with Cooling or Soft Dry.• After the operation mode has been selected, themode does not change.Heat Pump Model• At the beginning of the automatic operation, Heating,Cooling or Soft Dry is automatically selected accordingto the indoor temperature.• After the operation mode has been selected, themode does not change.OperationCoolingSoft DryStandardtemperature27°C24°CIndoortemperature24°COperationCoolingSoft DryHeatingStandardtemperature27°C24°C22°CIndoortemperature25°C21°CCooling ModelCOOL – 26°C ~ 28°CDRY – 1°C ~ 2°Clower than theroom temperatureHeat Pump ModelCOOL – 26°C ~ 28°CDRY – 1°C ~ 2°Clower than theroom temperatureHEAT – 20°C ~ 24°COFF/ONTEMPMODE FAN SPEEDAUTOTIMERAIR SWINGON/OFF SET/CRESET23541CH HOFF ON OFF ONAUTOCOOLFANFANSPEEDDRYSLEEPMANUAL622CS-A12ATP5 CU-A12ATP5 / CS-A18ATP5 CU-A18ATPT5 / CS-A24ATP5 CU-A24ATPT5