Panasonic CX-DVP292U Operating Instructions Manual

Also see for CXDVP292U - CAR DVD PLAYER: Operating instructions Service manual

Contents

Panasonic CX-DVP292U Operating Instructions Manual Manual pdf 22 page image

Supply voltage: 12 V DC (10.8 V–16 V), test voltage 14.4 V, negative groundCurrent consumption: Less than 2.0 ASignal system: NTSC 1.0 Vp-p 75 ≠ RCA pin jackDiscs played: (1) DVD-VIDEO disc5z (12 cm) single-sided, single-layer/double-layer5z (12 cm) double-sided, single-layer/double-layer3z (8 cm) single-sided, single-layer/double-layer3z (8 cm) double-sided, single-layer/double-layer(2) Compact disc (CD-DA, VIDEO CD, CD-ROM, CD-R, CD-RW)5z (12 cm) disc3z (8 cm) discAudio output level: 600 ≠ (2 ch 2.5 Vrms Max.)Audio signaloutput characteristics: (1) Frequency response: 20 Hz–20 kHz(2) S/N ratio: 95 dB (IHF, A)(3) Wow and Flutter: Below measurable limitsDimensions (WaHaD): 7za1 15/16za6 1/8z (178a50a155 mm)Weight: 3 lbs. 5 oz (1.5 kg)Digital audio output:†DTS only works with optical outputs.Above specifications comply with EIA standards.Note:≥ Specifications and design are subject to modification, without notice, due to improvements in technology.Disc Sound recording format Optical digital audio output from connectorDVD Dolby Digital Dolby Digital bitstream (1–5.1 ch)DTS† DTS bitstream (1–5.1 ch) (The analog portion is not output.)Linear PCM Linear PCM (2 ch)(48 kHz 16/20/24 bit) (48 kHz sampling/16 bit only)Video CD MPEG 1 MPEG 1 bitstreamLinear PCM Linear PCM (2 ch) (44.1 kHz sampling/16 bit)CD Linear PCM Linear PCM (2 ch) (44.1 kHz sampling/16 bit)DTS† DTS bitstream (1–5.1 ch) (The analog portion is not output.)MP3 MP3 Linear PCM (2 ch) (32 kHz/44.1 kHz/48 kHz sampling/16 bit )ENGLISH36SpecificationsElectrical Connections (continued)ENGLISH35CX-DVP292U45CX-DVP292U4444 45PARKING BRAKEChasissBattery Brake lamp 5 Clamp connectorParking brakeswitchSide brake (parking brake)connection lead(Blue/yellow stripe)Of the 2 cords emerging from the parking brake switch,connect the player’s parking brake cord to the one that isnot connected to the vehicle’s chassis while the brake isin the released state.Cords connected tothe vehicle.❐ Connecting side brake (parking brake) connection leadVehicle cordParking brake cordElementCoverPush the end of the cordin until it touches this part.3 Close the cover untilit snaps shut.1 Push the end of the side brakecord into the hole on the clampconnector.Place the vehicle cord into thegroove in the clamp connector.2 While making sure that the cordsdo not slip out of the clampconnector, press the elementdown with a pair of pliers.Caution:≥ For safety, be sure to ask your nearest professional installer to do this connection.The side brake (parking brake) switch positionvaries with the car model.For details on the exact location of the parkingbrake switch in your car, contact your dealer.“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.Side brake (parking brake)Foot brakeConnecting the Clamp Connector 5≥ Attach the clamp connector to the vehicle cord at a suitable position.≥ Note that if the cord being clamped onto is too thin (0.3 mm 2 or less), the connection may not beadequate.

/ 22

Related manuals for Panasonic CXDVP292U - CAR DVD PLAYER