Panasonic DMR-E55S Operating Instructions Manual

Also see for DMR-E55 Diga: Operating instructions Bedienungsanleitung

Contents

17RQT7444RecordingTimer recording[RAM] [DVD-R]You can enter up to 16 programmes up to a month in advance.Entering G- CODE numbers is an easy way of timer recording. You canfind these numbers in TV listings in newspapers and magazines.1 Press [G-Code].2 Press the numbered buttons to enterthe G- CODE number.Press [2] to move back to correct a digit.3 Press [ENTER].≥Confirm the programme and make corrections if necessaryusing [3, 4, 2, 1] (➡page 18, step 3).≥When “-- ---” appears in the “Name” column, you cannot settimer recording. Press [3, 4] to select desired programmeposition. After you have entered the information of a TVstation, it is kept in the unit’s memory.≥You can also press [REC MODE] to change the recordingmode.≥Programme NamePress [2, 1] to select “Programme Name” and press[ENTER] (➡ page 32).4 Press [ENTER].The settings are stored.Repeat steps 1–4 to programme other recordings.5 Press [F TIMER].The unit turns off and “F” lights on the unit’s display toindicate timer recording standby has been activated.[RAM]Even if the unit is in timer recording standby, play starts when youpress [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording workseven during play.Using G- CODE number to make timerrecordingsVOLUMECHINPUT SELECTDVDTVAV1 2 34 5 67 809MANUAL SKIPG-CodeCHCANCELSKIPSTOP PAUSE PLAY/x1.3SLOW/SEARCHFUNCTIONSENTERDIRECT NAVIGATORTOP MENURETURNSUB MENUCREATECHAPTERTIMERPROG/CHECKREC MODEERASE RECAUDIOTIME SLIPSTATUSDISPLAYFA B C-/--3,4,2,1ENTERF TIMERPROG/CHECKREC MODEG-Code¢ CANCELDIRECTNAVIGATORNumberedbuttons1:58 SPG-Code Remain12:53:00 15. 7. TUEEnter G-Code Number by using 0-9 keys.ModeStopStartName Date1:58 SPTIMERRECORDING Remain12:54:00 15. 7. TUEProgramme Name20:0019:0015/ 7 TUE SP1 ARD∫ To release the unit from recording standbyPress [F TIMER].The unit turns on and “F” goes out.≥Be sure to press [F TIMER] before the programme start time toput the unit on recording standby. Timer recording will work onlyif “F” is displayed.∫ To cancel recording when recording hasalready begunPress [F TIMER].≥You can also press and hold [∫] on the main unit for more than3 seconds to stop recording.[Note]≥“F” flashes for about 5 seconds when the unit cannot go totimer recording standby (e.g., a recordable disc is not in thedisc tray).≥If the unit is not put in the timer recording standby mode at thelatest 10 minutes before the programmed timer recordingstarting time, the “F” flashes on the unit display. In this case,press [F TIMER] to put the unit in the timer recording standbymode.≥When you programme successive timer recordings to startimmediately one after the other, the unit cannot record the partat the beginning of the later programmes (a few seconds whenrecording with DVD-RAM and approximately 30 seconds whenrecording with DVD-R).SP OK20:0019:00ARD 15/ 7 TUE01Mode DiscspaceStopStartNo. Name Date1:58 SPTIMERRECORDING Remain12:55:00 15. 7. TUENew Timer ProgrammeCheck to make sure“OK” is displayed.