Panasonic DMR-EH55S Operating Instructions Manual

Also see for Diga DMR-EH55: Owner's manual Operating instructions Setup guide Operating instructions

Contents

64RQT8365Channel/Clock settings when TV Guide On Screen TM system is not usedRefer to the control reference on page 60.Preparation:If the program listings have already been downloaded, return the unit to the factory preset condition using the steps indicated below.When the unit is on and stopped1 Press and hold [X CH] and [W CH] on the main unit for about fiveseconds.The unit turns off.2 Press [POWER Í/I] to turn the unit on.3 After the language and TV aspect is set up, press [RETURN] andexit the TV Guide On Screen TM system setup screen.[Note]You can record only manually after you set the unit with “Set Channels Automatically”.1 While stoppedPress [FUNCTIONS].2 Press [3, 4] to select “OtherFunctions” and press [ENTER].3 Press [3, 4] to select “Setup” andpress [ENTER].4 Press [3, 4] to select “Channel” andpress [1].5 Press [3, 4] to select “Set ChannelsAutomatically” and press [ENTER].6 Press [ENTER].Auto Channel Setting starts. This takes a few minutes.The unit then proceeds with Auto Clock Setting. The time isdisplayed when finished.≥DST, Daylight Saving Time, shows the summertime setting.Regarding DST (Daylight Saving Time) ➡ 22≥TIME ZONE shows the time difference from GreenwichMean Time (GMT).EST (Eastern Standard Time) l GMT j5CST (Central Standard Time) l GMT j6MST (Mountain Standard Time) l GMT j7PST (Pacific Standard Time) l GMT j8AST (Alaska Standard Time) l GMT j9HST (Hawaii Standard Time) l GMT j10For other areas: xx hr≥If the Auto Clock Setting does not start automatically, select“Clock Settings” from the “Setup” tab and then select “SetClock Automatically”.≥If the time was not set correctly, use “Set Clock Manually”(➡ 22) or adjust time zone.7 Press [ENTER].≥The unit configures channels according to the Signal Source(RF IN) settings as follows.Adjust the time zone (j1 or i1) if it was not set correctly with autoclock setting.You cannot change this setting if you set the clock manually.1 While stoppedPress [FUNCTIONS].2 Press [3, 4] to select “OtherFunctions” and press [ENTER].3 Press [3, 4] to select “Setup” andpress [ENTER].4 Press [3, 4] to select “Setup” andpress [1].5 Press [3, 4] to select “ClockSettings” and press [ENTER].6 Press [3, 4] to select “Adjust TimeZone” and press [ENTER].7 Press [3, 4] to select “s1” or “r1”and press [ENTER].To return to the previous screenPress [RETURN].To exit the screenPress [RETURN] several times.To cancel partway while Auto Channel/Clock Setting is taking placePress [RETURN].To set so the TV Guide On ScreenTM system is not displayed automatically when you turn the unit onWhen the power is turned on and the Start setup screen is displayed, press [3, 4] to select “Don’t remind me again” and press [ENTER].X CH WPOWER OPEN/CLOSE DRIVESELECTk 1 . 31 . 3RECCHS VIDEO VIDEO L/MONO-AUDIO-RIN2DV INPOWER Í/ lAuto channel/clock settingsChannelSetupSetupDiscVideoAudioSet Clock AutomaticallyAuto Clock Setting is complete.4/4/2005 12:15 AMDST.............. OnTime Zone..... CSTSignal Source(RF IN)Band ChannelAntenna VHF 2–13UHF 14–69CableTVVHF 2–13CATV LOW BAND 95–99CATV MID/SUPER BAND 14–36CATV HYPER BAND 37–65ULTRA BAND 66–94100–125SPECIAL CATV CHANNEL 1Adjust Time ZoneSetupSetupDiscVideoAdjust Time Zonej10i1Channel