Panasonic DMRBS750 - BLU-RAY DISC RECORDER Operating Instructions Manual

Also see for DMRBS750 - BLU-RAY DISC RECORDER: Help guide

Contents

Panasonic DMRBS750 - BLU-RAY DISC RECORDER Operating Instructions Manual Manual pdf 96 page image

96RQT9434Changing the unit’s settingsThese settings are used if you will connect this unit to a network.The connection to the Internet may take time or the internet may notbe connected depending on the connection environment.It is recommended that you use a broadband connection.∫ Testing the connectionAlways test the connection when a LAN cable is connected or whennew “IP Address / DNS Settings” have been made.1 Press [FUNCTION MENU].2 Press [3, 4] to select “Others” and press [OK].3 Press [3, 4] to select “Setup” and press [OK].4 Press [3, 4] to select “Network Settings” andpress [OK].5 Press [3, 4] to select “IP Address / DNSSettings” and press [OK].6 Press [3, 4] to select “Connection Test” andpress [OK].“Testing”: The test is in progress.“OK”: The connection is completed.“Failed”: Please check the connection and settings.[Note]≥Perform the “Connection Test” also when any change was made tothe “IP Address / DNS Settings”.≥If the connection test fails, it may be necessary to set the MACaddress of this unit at the router side. The MAC address can bedisplayed by selecting “Network Settings” and “IP Address / DNSSettings” in steps 1–5 (> above).∫ Setting the IP addressIn most cases, default settings can normally be used without makingany changes.Set the IP address only when the router has no DHCP serverfunctions or when the router’s DHCP server function is disabled.After performing steps 1–5 (> left)6 Press [3, 4] to select “IP Address Auto-assignment” and press [2, 1] to select “Off”.7 Press [3, 4] to select “IP Address”, “SubnetMask” or “Gateway Address” and press [OK].8 Enter numbers with the numbered buttons andpress [OK].≥After checking the specifications for your broadband router,enter each number.If the number is unknown, then check the number of otherdevices such as personal computers connected via a LANcable. Assign a different number from those of other devices forthe “IP Address” and the same number for others.≥If a wrong number is entered, then press [DEL].9 Press [2, 1] to select “Yes” and press [OK].[Note]≥The numeric input range is between 0 and 255.∫ Setting the DNS-IPIn most cases, default settings can normally be used without makingany changes.When setting an assigned DNS server from your internet serviceprovider, perform the following settings.After performing steps 1–5 (> left)6 Press [3, 4] to select “DNS-IP Auto-assignment” and press [2, 1] to select “Off”.7 Press [3, 4] to select “Primary DNS” or“Secondary DNS”and press [OK].8 Enter numbers with the numbered buttons andpress [OK].≥Follow the instructions given by your internet service providerand enter the numbers.If the number is unknown, then check the number of otherdevices such as personal computers connected via a LANcable and assign the same number.≥If a wrong number is entered, then press [DEL].9 Press [2, 1] to select “Yes” and press [OK].[Note]≥The numeric input range is between 0 and 255.∫ Setting the connection speedWhen the connection test results in “Failed” after the IP and DNS-IPaddresses are assigned, perform the following settings.After performing steps 1–5 (> left)6 Press [3, 4] to select “Connection Speed Auto-configure” and press [2, 1] to select “Off”.7 Press [3, 4] to select “Connection SpeedSetting” and press [2, 1] to select aconnection speed.≥Select a connection speed in accordance with the environmentof the network connected.≥When the settings are changed, the network connection may bedisabled depending on the device.Network SettingsPreparationConnect to the network. (> 103)RETURNOKIP Address / DNS SettingsConnection Test 䋭䋭䋭䋭OnOnOnOnOnOn㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄䋭䋭䋭䋭IP Address Auto-assignmentIP AddressSubnet MaskGateway AddressDNS-IP Auto-assignmentPrimary DNSSecondary DNSConnection Speed Auto-configureConnection Speed SettingMAC Address: 00-0b-97-e6-7a-ae192 . . .1IP AddressPlease input IP address and press “OK”.The IP address will be cleared by pressing“OK” when there is no number input.Press “DEL” button if a wrong number isentered.0 - Number9