Panasonic Diga DMR-EH50 Operating Instructions Manual

Also see for Diga DMR-EH50: Operating instructions Operating instructions Quick setup guide Operating instructions Operating instructions

Contents

62RQT8027MessagesOn the television PageOn the unit’s displayThe following messages or service numbers appear on the unit’s display when something unusual is detected during startup and use.Cannot finish recordingcompletely.≥The programme was copy-protected.≥The HDD or disc may be full.≥The maximum number of times you can record the program is exceeded.———Cannot playback.TV system is different from thesetting.To playback, please change the TVSystem in SETUP.≥You tried to play a title recorded using a different encoding system from that of the TV systemcurrently selected on the unit.Alter the “TV System” setting on this unit to suit.61Cannot record on the disc. ≥The disc may be dirty or scratched. 5Unable to format.Please check the disc.Cannot play on this unit. ≥You tried to play a non-compatible image.≥Turn the unit off and re-insert the card.356Cannot record. Disc is full. ≥[HDD] [RAM] Create space by erasing any unnecessary titles.[Even if you erase recorded content from the DVD-R or +R, there is no increase in disc space.Available space on DVD-RW (DVD-Video format) increases only when the last recorded title iserased.]≥Use a new disc.32, 39, 51—Cannot record. Maximum numberof titles exceeded.Error has occurred. Please pressENTER.≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering(“SELF CHECK” appears on the unit’s display).—No Disc ≥The disc may be upside down. —No folders. ≥There is no compatible folder in this unit. 11No SD CARDNo valid SD card.≥The card is not inserted. If this message is displayed with a compatible card alreadyinserted, turn off the unit, remove and then re-insert the card.≥The card inserted is not compatible or the card format does not match.611Not enough space on dubbingdestination.≥Create space by erasing any unnecessary items.≥Erase one or more items registered on the transfer (dubbing) list to ensure that the“Destination Capacity” is not exceeded.32, 35, 39,42, 5146, 49Please change the disc. ≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to removeit and check it for scratches or dirt. (The unit turns off automatically after you open the tray.)5This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R,DVD-RW (DVD-Video format), or +R.≥You inserted an unformatted DVD-RAM or DVD-RW.951This disc is not properlyformatted.Formatting is necessary usingDISC MANAGEMENT.$ ≥The operation is prohibited by the unit or disc. —REMOTE DVD (“∑” stands for a number.)≥The remote control and main unit are using different codes. Change the code on the remote control.Press and hold [ENTER] and the indicated number button at thesame time for more than 2 seconds.21HARD ERR ≥If there is no change after turning the unit on and off, consult the dealer where the unit waspurchased.—HDD SLP ≥In order to extend HDD life, the HDD is in SLEEP mode. Press [HDD] to activate. 4NO READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.≥This message may appear when the DVD-RAM lens cleaner has finished cleaning.Press [< OPEN/CLOSE] on the main unit to eject the disc.55PROG FULL ≥There are already 32 timer programmes. Delete unnecessary timer programmes. 29SELF CHECK ≥There was something unusual detected with the disc while recording, playing or transferring(dubbing), there was a power failure or the AC plug was disconnected while the unit was on. The unitis carrying out its recovery process. This process restores the unit to normal operation. The unit isnot broken. Wait until the message disappears.≥If “Quick Start” is set to “On”, “PLEASE WAIT” is displayed while the unit is carrying out its recoveryprocess. You cannot operate the unit while “PLEASE WAIT” is displayed.64—UNFORMAT ≥You have inserted a DVD-RAM or a DVD-RW that is unformatted or a DVD-RW recorded on anotherunit.—UNSUPPORT ≥You have inserted a disc the unit cannot play or record on. 9, 10U59 ≥The unit is hot.The unit switches to standby for safety reasons. Wait for about 30 minutes until the messagedisappears.Select a position with good ventilation when installing the unit. Do not block the cooling fan on therear of the unit.—U99 ≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby. Nowpress [Í/I] on the main unit again to turn the unit on.—X HOLD ≥The Child Lock function is activated.Press and hold [ENTER] and [RETURN] simultaneously until “X HOLD” disappears.54H or F ≥There is something unusual. (The service number displayed after H and F depends on the unit’scondition.)≥Check the unit using the troubleshooting guide. If the service number does not disappear, do thefollowing.1. Disconnect the plug from the household mains socket, wait a few seconds, then reconnect it.2. Press [Í/I] to turn the power on. (The unit may be fixed.)If the service number does not disappear despite after doing the above, request service from thedealer. Inform the dealer of the service number when requesting service.—64–67R:(e.g., R44:00)≥The unit is showing you the remaining time on the HDD or the disc. (This does not indicate amalfunction.)In the display across the letter “R” means “Remain” and the numbers mean remaining time(hours:minutes).22Messages