Panasonic FX-301-F Instruction Manual

Contents

INSTRUCTION MANUALDigital Fiber Sensor For Leak / Liquied Detection FiberFX-301(P)-FMJE-FX301F No.0034-46VThank you very much for purchasing Panasonic products.Please read this Instruction Manual carefully and thoroughly for the correctand optimum use of this product.Kindly keep this manual in a convenient place for quick reference. Make sure to connect the fiber attachment (FX-AT4), enclosed with the method. -pletely.! (FX-AT4) slowly into the fiber inlet till it stops(Note)." -tion, till it stops.# $% & the sensing becomes unstable.213Fiber lockleverFiber attachmentFiberMOUNTING2 1. Fit the rear part of the mounting section of the "' *#2. Press down the rear part of the mounting section "' *# front part of the mounting section to the DIN rail. 35mm width DIN rail12# $% on the rear portion of the mounting section is likely to break. + ! 7 12PART DESCRIPTION1Operation indicator(Orange)MODE indicator / RUN (Green)MODE keyJog switchMODE indicator / TEACH (Yellow)MODE indicatorOUT (Yellow)MODE indicator / ALL (Yellow)MODE indicator / ADJ (Yellow)MODE indicator / DISP (Yellow)Digital display (Red)Model indicator (Green) MODE key Jog switchPress Press Turn to “+” side Turn to“–” sideUsed for mode se-lection or cancella-tion during setting.(Note)U s e d t o s e l e c teach item. Used to enter each item.Note: When MODE key is pressed for 1 sec., or more, the sensor returns to the RUN mode.(in MAIN mode only)9 Never use this product as a sensing device for personnel protection.9 In case of using sensing devices for personnel protection, use productswhich meet laws and standards, such as OSHA, ANSI or IEC etc., forpersonnel protection applicable in each region or country.1. Holding the connector of the quick-connectioncable, align its release lever with the groove 2. Insert the connector till a click is felt.CONNECTION3 Note: Take care that if the connector is pulled out without pressing the release lever, the re-lease lever may break. Do not use a quick-connection cable whose release lever hasbroken. Further, do not pull by holding the cable, as this can cause a cable-break. 1. Pressing the release lever at the top of thequick-connection cable connector, pull out theconnector. Terminal No. Terminal name1 +V2 0V3 OutputMake sure to connect or disconnect the quick-connection cable in thepower supply off condition.GrooveQuick-connectioncableReleaseleverReleaselever123CASCADING AMPLIFIERS49 Make sure that the power supply is off while adding or removing the am-9 Make sure to check the allowable ambient temperature, as it depends 9 mount them on a DIN rail.9 ; *# fit them between the optional end plates (MS-DIN-E) mounted at thetwo ends.9 < = ' > ? -nected in cascade).9 When connecting more than two amplifiers in cascade, use the subcable (!"#) as the quick-connection cable for the second ampli- 9 ; to mount the optional end plate (MS-DIN-E) at both sides of each ampli- = &protection seal (FX-MB1) to the communication windows.9 Communication function is different between this amplifier and other =the communication window seal of the accessory amplifier protectionseal (FX-MB1) to the communication windows.9 In case of cascading, wait for 10 minutes, or more, to use the teachingfunction after the power is switched on. & "' *#! = other, and connect the quick-connection cables.3. Mount the optional end plates(MS-DIN-E) at both the ends to @ B % = plates. 1. Loosen the screws of the endplates.2. Remove the end plates.3. Slide the amplifiers and removethem one by one.Z [ MOUNTING.”Sub cable(!"#) (Optional)End plate(MS-DIN-E) (Optional)End plate(MS-DIN-E) (Optional)Main cable(!$#) (Optional) SlideSlide

/ 4

Related manuals for Panasonic FX-301-F