8http://panasonic‑electric‑works.net/sunxOverseas Sales Division (Head Office)2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, JapanPhone: +81-568-33-7861 FAX: +81-568-33-8591Europe Headquarter: Panasonic Electric Works Europe AGRudolf-Diesel-Ring 2, D-83607 Holzkirchen, GermanyPhone: +49-8024-648-0US Headquarter: Panasonic Electric Works Corporation of America629 Central Avenue, New Providence, New Jersey 07974, USAPhone: +1-908-464-355017 SpecificationsType standard type 2-output type Cable typeModel number NPN output FX-501 FX-502 FX-505-C2PNP output FX-501P FX-502P FX-505P-C2Supply voltage 12 to 24V DC % (+10% / ‑10%), ripple P‑P10% or lessPower consumption Normal operation: 960mW or less (current consumption 40mA or less at 24V supply voltage)Eco mode: 680mW or less (current consumption 28mA or less at 24V supply voltage)Output (FX-502□ and FX-505□-C2 only:output 1, output 2)nPn open-collector transistor● Maximum sink current (see note 2):FX-501: 100mAFX-502, FX-505: 50mA● Applied voltage: 30V DC or less between sensing output and 0V● Residual voltage: 2V or less (see note 3) at maximum sink currentPnP open-collector transistor● Maximum source current (see note 2):FX-501P: 100mAFX-502P, FX-505P: 50mA● Applied voltage: 30V DC or less between sensing output and +V● Residual voltage: 2V or less (see note 3) at maximum source currentNumber of outputs 1 2Output operation Switchable either Light‑ON or Dark‑ONShort‑circuit protection IncorporatedResponse time H-SP: 25μs or less, FAST: 60μs or less, STD: 250μs or less, LONG: 2ms or less, U-LG: 4ms or less, HYPR: 24ms or lessAnalog output (FX-505□-C2 only)— —● Output current: approx. 4 to 20mA(display in H‑SP, FAST, STD: 0to 4,000, display in LONG: 0 to8,000 (see note 4))● Response time: 2ms or less● Zero point: within 4mA ±1%F.S.● Span: within 16mA ±5%F.S.● Linearity: within ±3%F.S.● Load resistance: 0 to 250ΩExternal input (switchable with output 2 forFX-502□)— signal condition of nPn non-contact input:● High: +8V to +V DC or Open● Low: 0 to +1.2V DC (at 0.5mA source current)● Input impedance: Approx. 10kΩsignal condition of PnP non-contact input:● High: +4V to +V DC (at 3mA sink current)● Low: 0 to +0.6V DC or Open● Input impedance: Approx. 10kΩProtection IP40 (IEC)Ambient temperature ‑10 to +55°C (no dew condensation or icing allowed)● For 4 to 7 units mounted in cascade: ‑10 to +50°C● For 8 to 12 units mounted in cascade: ‑10 to +45°C)Storage: ‑20 to +70°CAmbient humidity 35 to 85% RH, Storage: 35 to 85% RHMaterial Enclosure: polycarbonate, switch: TPEE, protective cover: polycarbonateCable Cables are not supplied with the product. Select cables from the table below, 0.2 mm 2 6‑core cab tire cable, 2mWeight (main body only) Approx. 15g Approx. 60gAccessory FX-MB1 (Amplifier protection seal): 1 set.notes: 1. Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23°C.2. FX-501□: 50mA max. if 5 or more series connection types are connected together (25mA for FX-502□)3. Only if you are using the quick‑connection cable (optional, cable length 5m).4. If the digital display has been adjusted manually, the figures displayed may be outside the range.CableAmplifierCable length 1m Cable length 2m Cable length 5mMain cable Sub cable Main cable Sub cable Main cable Sub cableFX-501□ CN‑73‑C1 CN‑71‑C1 CN‑73‑C2 CN‑71‑C2 CN‑73‑C5 CN‑71‑C5FX-502 □ CN‑74‑C1 CN‑72‑C1 CN‑74‑C2 CN‑72‑C2 CN‑74‑C5 CN‑72‑C5* You can extend the cable up to 100m max. with 0.3mm 2 or more cable. However, in order to reduce noise, make the wiring as short as possible.