1029 High Speed High Accuracy Eddy Current Type Digital Displacement Sensor GP-X SERIESFIBERSENSORSLASERSENSORSPHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORSAREASENSORSLIGHTCURTAINSPRESSURE /FLOWSENSORSINDUCTIVEPROXIMITYSENSORSPARTICULARUSESENSORSSENSOROPTIONSSIMPLEWIRE-SAVINGUNITSWIRE-SAVINGSYSTEMSMEASURE-MENTSENSORSSTATICCONTROLDEVICESENDOSCOPELASERMARKERSPLC /TERMINALSHUMANMACHINEINTERFACESENERGYCONSUMPTIONVISUALIZATIONCOMPONENTSFACOMPONENTSMACHINEVISIONSYSTEMSUVCURINGSYSTEMSSelectionGuideLaserDisplacementMagneticDisplacementCollimatedBeamDigital PanelControllerMetal-sheetDouble-feedDetectionGP-XGP-ASPECIFICATIONSControllersType NPN output PNP outputItem Set model No. GP-XC□ GP-XC□-PSupply voltage 24 V DC ±10 % Ripple P-P 10 % or lessCurrent consumption 150 mA or lessResolution (Note 2) GP-XC3SE / GP-XC5SE: 0.04 % F.S. (64 times average processing)GP-XC8S / GP-XC10M / GP-XC12ML / GP-XC22KL: 0.02 % F.S. (64 times average processing)Sampling frequency 40 kHz (25 μs)Linearity (Note 2) Within ±0.3 % F.S.Temperature characteristics (Note 3) 0.07 % F.S./°C or lessAnalog voltage outputs Output voltage: –5 to +5 V (Note 4), Output impedance: 100 Ω approx.Response time 75 μs (maximum speed)Comparative outputs(HI, GO, LO)NPN open-collector transistor• Maximum sink current: 100 mA• Applied voltage: 30 V DC or less(between comparative output and 0 V)• Residual voltage: 1.6 V or less (at 100 mA sink current)0.4 V or less (at 16 mA sink current)PNP open-collector transistor• Maximum source current: 100 mA• Applied voltage: 30 V DC or less(between comparative output and +V)• Residual voltage: 1.6 V or less (at 100 mA source current)0.4 V or less (at 16 mA source current)Utilization category DC-12 or DC-13Output number HI / GO / LO 3 value outputOutput operationHI : ON when measured value > the upper limit valueGO: ON when upper limit value ≥ measured value ≥ lower limit valueLO : ON when lower limit value > measured valueShort-circuit protection IncorporatedExternal inputPhoto-coupler input• Input current: 9 mA or less• Operating voltage: ON voltage 17 V or more (between +24 V and input)OFF voltage 4 V or less (between +24 V and input)• Input impedance: 5 kΩ approx.Photo-coupler input• Input current: 9 mA or less• Operating voltage: ON voltage 17 V or more (between 0 V and input)OFF voltage 4 V or less (between 0 V and input)• Input impedance: 5 kΩ approx.Serial I/O RS-232CZero-set setting method Push button setting / External input settingIndicatorsMODE Orange LED (lights up when in mode status)HI Orange LED (lights up when the upper limit value is exceeded)GO Green LED (lights up when within the upper and lower limit value)LO Orange LED (lights up when less than the lower limit value)TIMING Green LED (lights up as per the external or internal trigger timing)Upper level digital display part 5 digit orange LED (display of numerical values out of upper and lower limit value)Lower level digital display part 5 digit green LED (display of numerical values within the upper and lower limit value)Environmental resistancePollution degree 3 (Industrial environment)Ambient temperature 0 to +50 °C +32 to +122 °F (No dew condensation), Storage: 0 to +50 °C +32 to +122 °FAmbient humidity 35 to 85 % RH, Storage: 35 to 85 % RHEMC EN 61000-6-2, EN 61000-6-4Vibration resistance 10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours eachShock resistance 100 m/s 2 acceleration (10 G approx.) in X, Y and Z directions for five times eachMaterial Enclosure: PolycarbonateWeight Net weight: 120 g approx.Accessory ATA4811 (Controller mounting frame): 1 setNotes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.2) This value was obtained at a constant +25 °C +77 °F.3) This value represents 20 to 60 % of the maximum sensing distance when combining the sensor head and controller.4) Adjusted to a 0 to +5 V factory setting.