Panasonic KX-FP81BX Service Manual

Contents

(Cause and Countermeasure)As shown in the chart above, the total handshaking time must be reduced, but because of the long distance connection and linkingof several stations, the line connection time cannot be reduced. Accordingly, the following countermeasures should be tried.(A)... As the 35 sec. count is started directly after dialing or directly after the START button has been pressed for models with aSTART button, the other party should be called manually, if possible. Another possibility is entering two pauses at the end of theauto dial number on the transmission side. Then the count start time can be delayed for 2 pauses (about 10 sec.).Cause 2:Erroneous detection because of an echo or an echo canceler.(Echo/Echo Canceler)The signal from FAX1 reaches FAX2 via stations 1 and 2, but the reflection signal at station 2 also returns via station 1 (echo). Asthe distance between station 1 and station 2 is far, the echo returns to FAX 1 at a max of 600 msec after transmission. There isa possibility that this signal is detected erroneously as the signal from FAX2. For a normal call, there is also a possibility that theecho of their own voice will make the call difficult to understand. For this reason, each station (station 1 and station 2) attaches echocancelers (S1 and S2) for international lines or long distance lines. For the echo canceler, the level of the transmission signal fromFAX 1 is compared with the level of the reception signal from FAX2. When the transmission signal is larger, S1 is closed while S2is opened when it is smaller. In other words, for transmission from FAX1, S1 is closed and S2 is open, so that the echo does notreturn to FAX1.(Causes and Countermeasures)(Cause A)When a training signal is transmitted from FAX1 during the communication procedure at the time of transmission from FAX1 toFAX2, there is a delay until the echo canceler operates. S1 is closed so that a part of the head of the training signal may drop out.Normal reception by FAX2 may not be possible, and transmission may not be started.(Countermeasure A)When the international line mode is ON in the service mode (code No. 521), a dummy signal is attached to the head of the trainingsignal to prevent this problem. As this is normally ON, it is necessary to reconfirm that this has not become OFF. When theinternational mode is switched OFF, the transmission side will try the training signal three times at each speed (9600BPS, 4800BPSand 2400BPS). If NG, it will drop the speed by one rank (fall-back). When the international mode is switched ON, each speed willbe tried only twice. In other words, the slower speed with fewer errors can be accessed more easily. This is done because the lineconditions may deteriorate and the picture may be disturbed more easily during communication for international lines or longdistance communication, even when the training is OK. The default value is ON as preference is given to clearer pictures ratherthan speed.(Cause B)The echo canceler operation stops with a 2100Hz signal. (i.e. S1 and S2 become ON). Accordingly, when FAX1 has executedautomatic reception, a CED signal is output. If this signal is 2100Hz, S1 and S2 will become ON. Then the echo of the DIS signaloutput afterwards may be received and FAX1 may execute an erroneous operation, preventing communication from starting.(Countermeasure B)In the service mode, the CED signal frequency is set to 1100 Hz (code No.520), or the time setting between the CED signal andthe DIS signal is set from 75 msec to 500 msec in the service mode (code No.593). This is because the echo canceler operationstop mode is canceled by an interval of 250 msec or more.Reduce receiving sensitivity to reduce the effect of RCV echo signal. (Service mode: code No. 598)51KX-FP81BX / KX-FP81CX / KX-FP82CX