Panasonic LS-H Series Instruction Manual

Also see for LS-H Series: Instruction manual Instruction manual

Contents

specifications

Panasonic LS-H Series Instruction Manual Manual pdf 1 page image

CAUTIONS3This product has been designed to meet the specifications when it is usedalong with the optional exclusive amplifier. If an amplifier other than theexclusive amplifier is used, not only the specifications may not be met, butit may also be a cause for malfunction or break down. Hence, pleaseensure to use this product along with the optional exclusive amplifier.●●●●●●●●●●●●●●●This product has been developed / produced for industrial use only.Always use the sensor with the connector to be joined to the amplifier.Make sure that the power is off while wiring to the amplifier.In case noise generating equipment (switching regulator, inverter motoretc.) is used in the vicinity of this product, connect the frame ground(F.G.) terminal of the equipment to an actual ground.If power is supplied from a commercial switching regulator, ensure thatthe frame ground (F.G.) terminal of the power supply is connected to anactual ground.Do not use the sensor during the initial transient time (0.5 sec.) just afterthe power supply is switched on.Do not run the wires together with high-voltage lines or power lines or putthem in the same raceway. This can cause malfunction due to induction.Take care that the sensor head is not directly exposed to fluorescentlamp from a rapid-starter lamp or a high frequency lighting device, as itmay affect the sensing performance.The sensor head cable cannot be extended.Make sure that stress is not applied to the sensor head cable joint.This sensor is suitable for indoor use only.Do not allow any water, oil fingerprints, etc., which may refract light, ordust, dirt, etc., which may block light, to stick to the emitting/receivingsurfaces of the sensor head. In case they are present, wipe them with aclean, soft cloth or lens paper.Do not use the sensor in vaporous, dusty or corrosive gas atmospheres.Take care that the sensor does not come in contact with water, oil,grease or organic solvents, such as, thinner, etc.Make sure that the power is off while cleaning the emitting/receivingwindows of the sensor head.SPECIFICATIONS2Notes: 1)2)3)4)The model No. with suffix '-C5' stands for the 5m cable length type.(e.g.) LS-H91-C5The model No. of retroreflective type sensor with the suffix '-Y' is the sensor without the RF-330and RF-230 reflector. Arrange the reflector separately.(e.g.) LS-H91-YLS-H22 is the model No. for the long sensing range spot reflective type (LS-H21) with thelens attachment for line reflective type (LS-MR1). 'LS-H21' is indicated on the actual product.Configure the mode settings in the applicable amplifier LS-400 series.Connector foramplifier: 1 pc.RF-330 (Reflector): 1 pc.Warning labelJapanese / English/ Chinese: 1 setConnector foramplifier: 1 pc.RF-230 (Reflector): 1 pc.Warning labelJapanese / English/ Chinese: 1 setConnector foramplifier: 1 pc.Warning labelJapanese / English/ Chinese: 1 setConnector foramplifier: 1 pc.LS-MR1 (Lensattachment for linereflective type): 1 pc.Warning labelJapanese / English/ Chinese: 1 set0.2 to 10m0.2 to 10m0.2 to 20m0.2 to 30mLS-H9235～85% RH, Storage: 35～85% RHSensingrange(Note 4)0.1 to 3m 30 to 300mm 30 to 300mmH-SP mode0.1 to 3m 30 to 300mm 30 to 300mmFAST mode0.1 to 5m 30 to 500mm 30 to 500mmSTD mode0.1 to 7m 30 to 1,000mm 30 to 1,000mmU-LG modeLS-400 seriesApplicable amplifierModel No. (Note 1)Item LS-H21LS-H91Long sensing rangespot reflectiveLong sensingrangeLS-H22 (Note 3)Long sensing rangeline reflectiveDiffuse reflective typeTypeCoaxial retroreflective type (Note 2)Accessories30g approx.Weight0.1mm 2 shielded cable, 2m longCableEnclosure: PBT (Attachment: PEI), Lens cover: AcrylicMaterialRed semiconductor laser Class 2 (IEC/JIS/GB/KS standard)(Max. output: 3mW or less, Peak emission wavelength: 655nm)Emitting element-10 to +55℃ (No dew condensation or icing allowed), Storage: -20 to +70℃Ambient humidityAmbient temperatureGreen LED (Lights up when laser is emitted)Laser emission indicatorOrange LED (Lights up when amplifier output is ON)Operation indicatorThank you very much for purchasing Panasonic products. Read this InstructionManual carefully and thoroughly for the correct and optimum use of this product.Kindly keep this manual in a convenient place for quick reference.●●●●Never use this product as a sensing device for personnel protection.In case of using sensing devices for personnel protection, useproducts which meet standards, such as OSHA, ANSI or IEC etc.,for personnel protection applicable in each region or country.Do not view direct beam by the unprotected eye or with anoptical instrument. Lasers are potentially hazardous.Use of control or adjustment or performance of proceduresother than those specified in this instruction manual mayresult in hazardous radiation expose.WARNINGLS-H SeriesLaser Sensor HeadINSTRUCTION MANUALMJE-LSH No.0059-56VFOR SAFE USE OF A LASER PRODUCT1● In order to prevent the accident by laser product and protect the users,JIS C 6802 -2014 “Safety of laser products” was established based on theregulation of IEC (International electrotechnical Commission). Thisregulation classifies laser products according to the level of hazard, andprovides the safety measures for respective classes.This product are classified as “Class 2 laser products” according toIEC 60825-1 -2014 (JIS C 6802 -2014) “Safety of laser products”.● Laser hazardous classClassification according to IEC 60825-1 -2014 (JIS C 6802 -2014 )Description of hazardous evaluationClassVisible beam, low power. Blink response of eye affords protection.Class 2●・The following label is affixed on this product in accordance with theSafety of laser product.Warning labelIn Japanese (Based on JIS C 6802 -2014 ) In English (Based on IEC 60825-1 -2014 )In Chinese (Based on GB 7247.1 -2012 )● When this product is used in China,affix the chinese warning label(accessory) on the label in theproduct.・ Laser emission indicator (green)While laser is emitted, the laser emission indicator (green) of the sensorhead lights up.This indicator is visible even when wearing laser protective glasses.Operation indicator (Orange)Laser emission indicator (Green)Direction oflaser emission● If the affixed label on this product may not be visible after installation ofthe product, affix the accessory lable close to the product where you cansee.In Japanese In English In Chineseクラス1レーザ製品JIS C 6802Direction oflaser emissionクラス1レーザ製品JIS C 6802Direction oflaser emission

/ 2

Related manuals for Panasonic LS-H Series