Chapter 4 Settings — [PROJECTOR SETUP] menu96 - ENGLISH3) Press as to select [EMULATE].4) Press the button.f The [EMULATE] screen is displayed.5) Press as to select an item.[DEFAULT]EZ590 series, EW650 series, EW550 series, EX620 series, EX520 series, FZ570 series, FW530series, FX500 series, RZ570 series, VW355N series, VX425N series, VW350 series, VX420 series,VZ575N series, VW535N series, VX605N series, VZ570 series, VW530 series, VX600 series, VX60,VX50, EZ580 series, EW640 series, EX610 series, EW540 series, EX510 series, VW345N series,VX415N series, VW340Z, VX410Z, VX42Z, VX406EA, VX46EA, EZ770 series, EW730 series, EX800series, RZ475 series, RZ470 series, RW430 series, RZ370 series, RW330 series[D3500] D3500 series[D4000] D4000 series[D/W5k SERIES] D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series[D/W/Z6k SERIES]DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series, DW730series, DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, D5000 series,DZ570 series, DW530 series, DX500 series[L730 SERIES] L730 series, L720 series, L520 series[L780 SERIES] L780 series, L750 series[L735 SERIES] L735 series[L785 SERIES] L785 series[F/W SERIES] FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series[LZ370] LZ370 series[LB/W SERIES] LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series, LB78series, LB75 series[VX500 SERIES] VW435N series, VW440 series, VW430 series, VX505N series, VX510 series, VX501U, VX405KEA,VX45KEA, VX500 series, VW330 series, VX400NT series, VX400 series, VX41 series[EZ570 SERIES] EZ570 series, EW630 series, EW530 series, EX600 series, EX500 series[VW431D] VW431D series6) Press the button.Note(Only for PT-EZ590, PT-EW650 and PT-EX620)f When [INPUT SELECT] is set to [DIGITAL LINK], communication using that serial terminal is available only when the corresponding device(such as the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G)) is connected to the LAN> terminal.f When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for “NOSIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.f When [INPUT SELECT] is set to [DIGITAL LINK], communication speed is fixed to 9 600 bps.[REMOTE1 MODE]Set the terminal.1) Press as to select [REMOTE1 MODE].2) Press qw to switch the item.f The items will switch each time you press the button.[DEFAULT] The pin assignment of the terminal is used by the factory default setting of theprojector.[USER] Used to change the setting of the terminal.[F/W SERIES] The setting of the terminal is used for the F/W series compatibility.f When [USER] is selected, proceed to Step 3).3) Press the button.4) Press as to select one from [PIN2] to [PIN8], and press qw to switch the setting.[FUNCTION BUTTON]The function assigned to the button of the remote control is displayed. You can also release theassigned setting.
