Panasonic PT-LM1U Operating Instructions Manual

Also see for PTLM1U - LCD PROJECTOR: Specifications

Panasonic PT-LM1U Operating Instructions Manual Manual pdf 2 page image

2-ENGLISH E NGLISH -3 PreparationIMPORTANT SAFETY NOTICEDear Panasonic Customer:This instruction booklet provides all the necessary operating information that youmight require. We hope it will help you to get the most out of your new product,and that you will be pleased with your Panasonic LCD projector.The serial number of your product may be found on its bottom. You should noteit in the space provided below and retain this booklet in case service is required.Model number: PT-LM1USerial number:WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.The exclamation point within an equilateral triangle isintended to alert the user to the presence of importantoperating and maintenance (servicing) instructions in theliterature accompanying the product.Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60Hz AC, house current only.CAUTION: The AC power cord which is supplied with the projector as an accessory canonly be used for power supplies up to 125 V, 7 A. If you need to use highervoltages or currents than this, you will need to obtain a separate 250 Vpower cord. If you use the accessory cord in such situations, fire may result.CAUTION:This equipment is equipped with a three-pin grounding-type powerplug. Do not remove the grounding pin on the power plug. Thisplug will only fit a grounding-type power outlet. This is a safetyfeature. If you are unable to insert the plug into the outlet, contactan electrician. Do not defeat the purpose of the grounding plug.Do not removeWARNING:B Not for use in a computer room as defined in the Standard for theProtection of Electronic Computer/Data Processing Equipment,ANSI/NFPA 75.B For permanently connected equipment, a readily accessible disconnectdevice shall be incorporated in the building installation wiring;B For pluggable equipment, the socket-outlet shall be installed near theequipment and shall be easily accessible.WARNING:This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.– Consult the dealer or an experienced radio/TV technician for help.FCC CAUTION: To assure continued compliance, use only shielded interface cables whenconnecting to computers or peripheral devices.Any unauthorized changes or modifications to this equipment will void theusers authority to operate.Declaration of ConformityModel Number: PT-LM1UTrade Name: PanasonicResponsible party: Matsushita Electric Corporation of America.Address: One Panasonic Way Secaucus New Jersey 07094Telephone number: 1-800-528-8601 or 1-800-222-0741Email: pbtsservice@panasonic.comThis device complies with Part 15 of the FCC Rules, Operation is subject tothe following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.