Panasonic SC-MAX9000 Operating Instructions Manual

Also see for SC-MAX5000: Operating instructions User manual

22 RQT0A6622“TEMP NG”• The temperature protection circuit has been activated, andthe system will switch off. Let the unit cool down beforeswitching it on again.• Check that the ventilation opening of the unit is notobstructed.• Ensure this unit is well ventilated.“TRK FULL”• The number of files has exceeded the supported limit.“USB A NO DEVICE”“USB B NO DEVICE”• The USB device is not connected. Examine the connection.“USB OVER CURRENT ERROR”• The USB device is using too much power. Disconnect theUSB device, switch off the system and then switch onagain.“VBR”• The system cannot show the remaining play time forvariable bit rate (VBR) tracks.Remote control codeWhen other Panasonic equipment responds to theremote control of this system, change the remote controlcode for this system.PreparationPress [CD/RADIO/AUX] to selectSC-MAX9000 SC-MAX7000 : “AUX 1”, “AUX 2”, “AUX 3” or“AUX 4”.SC-MAX5000 : “AUX 1” or “AUX 2”.█ To set the code to “REMOTE 2”1 Press and hold [CD/RADIO/AUX] on the main unitand [2] on the remote control until “REMOTE 2” isshown.2 Press and hold [OK] and [2] for a minimum of4 seconds.█ To set the code to “REMOTE 1”1 Press and hold [CD/RADIO/AUX] on the main unitand [1] on the remote control until “REMOTE 1” isshown.2 Press and hold [OK] and [1] for a minimum of4 seconds.System memory resetReset the memory when the following situations occur:• There is no response when buttons are pressed.• You want to clear and reset the memory contents.1 Disconnect the AC mains lead.2 While you press and hold [1] on the main unit,connect the AC mains lead again.Continue to press and hold the button until“– – – – – – – – –” is shown.3 Release [1].All the settings are set back to the factory preset.It is necessary to set the memory items again.Specifications█ Amplifier sectionRMS output power stereo modeSC-MAX9000High Ch 500 W per channel (3 Ω), 1 kHz, 30% THDMid Ch 500 W per channel (3 Ω), 1 kHz, 30% THDLow Ch 1000 W per channel (5 Ω), 100 Hz, 30% THDTotal RMS stereo mode power 4000 WSC-MAX7000Front Ch 350 W per channel (3 Ω), 1 kHz, 30% THDFront Ch 350 W per channel (3 Ω), 1 kHz, 30% THDSubwoofer Ch 800 W per channel (6 Ω), 100 Hz,30% THDTotal RMS stereo mode power 3000 WSC-MAX5000High Ch 350 W per channel (3 Ω), 1 kHz, 30% THDMid Ch 350 W per channel (3 Ω), 1 kHz, 30% THDLow Ch 500 W per channel (2 Ω), 100 Hz, 30% THDTotal RMS stereo mode power 2400 W█ Tuner sectionFrequency modulation (FM)Preset memory 30 stationsFrequency range87.50 MHz to 108.00 MHz (50 kHz step)Antenna terminals 75 Ω (unbalanced)Amplitude modulation (AM)Preset memory 15 stationsFrequency range 522 kHz to 1629 kHz (9 kHz step)520 kHz to 1630 kHz (10 kHz step)█ Disc sectionDisc played (8 cm or 12 cm)CD, CD-R/RW (CD-DA, MP3 )MPEG-1 Layer 3, MPEG-2 Layer 3Pick upWavelength 790 nm (CD)█ Bluetooth® sectionVersion Bluetooth ® Ver. 2.1 + EDRClass Class 2Supported profiles A2DP, AVRCP, SPP, OPP, FTPOperating frequency 2.4 GHz band FH-SSOperation distance 10 m line of sight