208.3. Disassembly ProcedureNo. Item Fig Removal1 Lens Hood Unit Fig. D1 Lens Hood Unit2 Side Case (R) Unit Fig. D2 3 Screws (A)2 Screws (B)1 Screw (C)Fig. D3 Hinge Ornament3 Screws (D)Fig. D4 FP6103(Flex)Side Case (R) UnitFig. D5 NOTE (When Installing)3 Side Case (L) CoverUnitFig. D6 1 Screw (E)1 Screw (F)Fig. D7 1 Screw (G)2 Screws (H)Fig. D8 2 Locking tabsSide Case (L) Cover Unit4 Front Case Unit Fig. D9 3 Screws (I)2 Ribs1 Locking tabFig. D10 P6701(Flex)Front Case UnitFig. D11 Discharge the Capacitor5 Rear Case Unit Fig. D12 1 Screw (J)Fig. D13 1 Screw (K)Fig. D14 FP6104(Flex)Rear Case Unit6 Top Case Unit Fig. D15 FP6101(Flex)FP7001(Flex)Fig. D16 2 Screws (L)Top Case Unit7 Main (R) PCB Fig. D17 2 Screws (M)FP6102(Flex)Fig. D18 PP6101(Connector)FP6105(Flex)Main (R) PCB8 Lens Unit Fig. D19 FP6001(Flex)FP6002(Flex)1 Screw (N)Lens Unit9 Main (L) PCB Fig. D20 2 RibsMain (L) PCB10 Front PCB Fig. D21 P4001(Connector)2 Screws (O)Front PCB11 LCD Unit Fig. D22 1 Screw (P)LCD OPEN/CLOSEdetection switchFig. D23 2 Screws (Q)LCD UnitFig. D24 NOTE (When Installing)12 Monitor PCB Fig. D25 2 Screws (R)2 Screws (S)LCD Case TopFig. D26 FP901(Flex)FP902(Flex)LCD Hinge Unit1 RibMonitor PCB13 LCD Fig. D27 Reflection SheetLight PanelDiffusion SheetPrism Sheet (B)Prism Sheet (A)Fig. D28 2 Screws (T)LCD Reinforcement AngleLight Panel HolderLCDLCD Shield CaseLCD Case Bottom14 SD Cover, SD CoverDetection Knob,SD Cover DetectionSpringFig. D29 SD Cover Detection SpringSD Cover Detection KnobFig. D30 SD Cover ShaftFig. D31 SD CoverSD Cover SpringFig. D32 2 Locking tabsSD Cover Lock LeverSD Cover Lock SpringSD Open Button15 Mic PCB Fig. D33 Solder (3 points)1 Screw (U)Mic PCB16 ECM Flex Unit,Flash UnitFig. D34 3 Screws (V)Top CaseFig. D35 ECM Flex UnitMic DumperFig. D36 1 Screw (W)Switch part of Flash FlexUnit2 Screws (X)Flash Base UnitFig. D37 1 Screw (Y)2 Locking tabsFlash CaseFig. D38 Flash Insulation Sheet2 Locking tabsFlash Unit17 Rear Case,Rear Operation UnitFig. D39 2 Screws (Z)Jack Cover UnitFig. D40 2 Ribs1 HookRear Operation Unit18 Barrier Motor Unit Fig. D41 3 Screws (a)Front Angle (L)Front Angle (R)Barrier Motor UnitBarrier Select KnobFig. D42 NOTE (When Installing)19 Prism Unit,Optical FilterFig. D43 1 Screw (b)CCD Heat Sink Plate2 Screws (c)Prism UnitOptical Filter20 Iris Unit Fig. D44 Solder (20 points)4 Screws (d)3 RibsFig. D45 Iris Unit21 Zoom Motor Unit Fig. D46 2 Screws (e)Zoom Motor Unit22 Focus Motor Unit Fig. D47 2 Screws (f)Focus Motor UnitNo. Item Fig RemovalDownloaded From CamcorderManual.com Panasonic Manuals