Philips 4000 Series Manual

Also see for 4000 series: Quick start guide User manual Quick start guide Service manual Quick start guide

1 NoticeTrademarks are the property of Koninklijke Philips N.V. ortheir respective owners.P&F USA reserves the right to change products at any timewithout being obliged to adjust earlier supplies accordingly.The material in this manual is believed adequate for theintended use of the system. If the product or its individualmodules or procedures are used for purposes other thanthose specified herein, confirmation of their validity andsuitability must be obtained. P&F USA warrants that thematerial itself does not infringe any United States patents. Nofurther warranty is expressed or implied.P&F USA cannot be held responsible neither for any errorsin the content of this document nor for any problems as aresult of the content in this document. Errors reported to P&FUSA will be adapted and published on the P&F USA supportwebsite as soon as possible.Pixel characteristicsThis LCD product has a high number of color pixels. Althoughit has effective pixels of 99.999% or more, black dots or brightpoints of light (red, green or blue) may appear constantly onthe screen. This is a structural property of the display (withincommon industry standards) and is not a malfunction.WarrantyNo components are user serviceable. Do not open or removecovers to the inside of the product. Repairs may only be doneby Service Centers and official repair shops. Failure to do soshall void any warranty, stated or implied.Any operation expressly prohibited in this manual, anyadjustments or assembly procedures not recommended orauthorized in this manual shall void the warranty.Federal Communications Commission NoticeThis equipment has been tested and found to comply withthe limits for a Class B Digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may causeharmful interference to radio communications. However,there is no guarantee that interference will not occur in aparticular installation. If this equipment does causeharmful interference to radio or television reception, whichcan be determined by turning the equipment off and on,the user is encouraged to try to correct the interference byone or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.• Consult the dealer or an experienced radio or television technicianfor help.Declaration of ConformityTrade Name : PHILIPSResponsible Party : P&F USA, Inc.Model : 43PFL4902Address : PO Box 2248, Alpharetta, GA30023-2248 U.S.A.Telephone Number : 1 866 813 3283ModificationsThis apparatus may generate or use radio frequency energy.Changes or Modifications to this apparatus may causeharmful interference.Any Modifications to the apparatus must be Approved byP&F USA.The user could lose the authority to operate this apparatusif an unauthorized Change or Modification is made.CablesConnections to this device must be made with shieldedcables with metallic RFI / EMI connector hoods to maintaincompliance with FCC Rules and Regulations.Canadian noticeCAN ICES-3 (B)/NMB-3 (B)Analog and Digital Television Receiving Apparatus,Canada BETS-7 / NTMR-7.The following FCC/IC RSS applies to theWireless LAN adapter included in this product.FCC Caution: Any changes or modifications not expresslyapproved by the party responsible for compliance couldvoid the user’s authority to operate this equipment.This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.Country Code StatementFor product available in the USA market, only channel 1a1 1can be operated. Selection of other channels is not possible.To maintain compliance with FCC RF exposure requirements,use only belt-clips, holsters or similar accessories that do notcontain metallic components in its assembly. The use ofaccessories that do not satisfy these requirements may notcomply with FCC RF exposure requirements and should beavoided.This device complies with Industry Canada license-exemptRSS standard(s). Operation is subject to the following twoconditions: (1) this device may not cause interference and (2)this device must accept any interference, including interferencethat may cause undesired operation of the device.5150-5250 MHz band is restricted to indoor operations only.High-power radars are allocated as primary users (i.e.priority users) of the bands 5250-5350 MHz and5650-5850 MHz and that these radars could causeinterference and/or damage to LE-LAN devices.Compliance with IC requirement RSS-210A9.4.4Data transmission is always initiated by software, which isthe passed down through the MAC, through the digital andanalog baseband, and finally to the RF chip. Several specialpackets are initiated by the MAC. These are the only waysthe digital baseband portion will turn on the RF transmitter,which it then turns off at the end of the packet. Therefore,the transmitter will be on only while one of theaforementioned packets is being transmitted. In otherwords, this device automatically discontinue transmissionin case of either absence of information to transmit oroperational failure.To obtain a more detailed electronic copy of this User Manual or to access live chat support, go to www.philips.com/support4