![Reefe VSRM Series User Manual Manual pdf 5 page image](https://manuals-archive2.s3.amazonaws.com/4207939/af88927055027dfb25e004c7743e2b165f.jpg)
Reefe VSRM Series User Manual
![]()
Page | 5 Ascento 37 Export St Lytton QLD PH: 1800 807 604 | VSRM Inverter Contant Pressure Pumps | V2016.123.4 IMPORTANT NOTE: If using the VSRM Pump as a townwater booster system (mains water pressure booster) setthe OPERATING PRESSURE as: Mains pressure + (65% of max pump head pressure – up to maximum of 80% of maxpump pressure) refer to the table above. CONTACT sales@ascento.com.au for a diagram showing the CORRECTconfiguration for Mains Water boosting applications, warranty is void if it is not configured to our specifications.3.5 IMPORTANT NOTE: If using the VSRM Pump with a townwater backup system (Rain-Mains System) you must fita FLOAT SWITCH to the rainwater tank so that when the water level of the tank is 300mm above the tank outlet, thepower to the pump is turned OFF, BEFORE the tank and pipes are dry. We recommend the RainPro Rain-MainsValveset with a REEFE Pump Shut-Off Controller with Float Switch. Or use a “Piggy-Back” Float Switch, but ensurethe installation is checked and approved by a licenced electrician.3.6 IMPORTANT NOTE: The pump will run on continuously if;a) There is any leaks anywhere in the pipework – do a pressure-test to rule this out – do not assume that thepump is faulty – pump running continuously is almost always due to a leak, or point c) below!b) If you have drip irrigation that is not set up correctlyc) The pressure setting is too high it will not stop – this is not a pump fault – ensure pressures are set correctlyrefer to “3.3 Important Note”If the pump runs continuously, and you find it is leaks or drip irrigation that you cannot find or stop, youMUST install an additional larger PRESSURE TANK between the pump and the first point of discharge, toavoid the continuous running. We suggest a REEFE Pressure Tank PT35H or larger. Warranty is voided bycontinuous running of the pump.3.7 COMPONENT DIAGRAM AND INSTALLATION INSTRUCTIONSNo. Component No. Component1 Pump body Wet-End 7 Pressure tank2 Motor 8 Pressure gauge3 Mounting plate 9 Five-way Valve4 Fan housing 10 Pressure Transducer5 Inverter components 11 Water Outlet6 Power plug 12 Water InletInstallation Guide – refer also to the diagrammatic instruction manual1. Read the manual carefully before installation and use. ALSO REFER to the separate diagrammatic instructionsand read them in conjunction with this manual.2. Check the pump, motor casing and the power plug for damage before installation, do not use if it is damaged inany way.3. Pump must be installed on a level concrete pad, or similar material that will remain level and not subside. Don'tinstall the VSRM underwater or in any place where water may be splashed or sprayed onto the controller, it mustbe in a well ventilated and well drained area, protected from the weather, dust, dirt, leaves, insects, rodents,reptiles etc, by way of a pump cover or a weatherproof enclosure. Installation under eaves of houses is not anacceptable level of protection from the weather.The pump must be easily accessible for servicing and repairs if ever necessary – do not install in any of the followingareas: confined space, crawl space, under a house with enclosed base, roof space, beside bedrooms, close toneighbours bedrooms, or in any other area that makes it difficult or impossible to easily access the pump.4. Pump must be earthed correctly, and connected to a dedicated circuit with the correct power circuit according tothe power requirements of the pump, having an integral Safety Switch (RCD) having a rated residual operatingcurrent not exceeding 30mA.5. Check the operating environment is suitable for this Pump – do not use in hazardous areas or for liquids otherthan clean fresh water. |
Related manuals for Reefe VSRM Series
This manual is suitable for:
![Manuals database logo](/_next/static/media/manuals_logo.28807196.png)
manualsdatabase
Your AI-powered manual search engine