Sanyo 42LM4WPN Instruction Manual

Contents

2SAFETYSAFETY PRECAUTIONSPRECAUTIONS GBDo not allow anything to rest on the powercord. Do not locate this LCD monitor wherethe cord will be damaged by people walkingon it.Do not overload wall outlets and extensioncords as this can result in fire or electricshock.Do not place this LCD monitor near any heat sources such asradiators, heaters, stoves and other heat-generating products(including amplifiers).Do not place your LCD monitor on an unstable stand, shelf ortable. Serious injury to an individual, and damage to the LCDmonitor may result if it should fall. Your sales person canrecommend approved wall mounting kit. A special wall mountingkit is available for this model.This LCD monitor should be operated only from the type of powersource indicated on the monitor or as indicated in the OperatingInstructions. If you are not sure of the type of power supply, con-sult your sales person or your local power companyFor added protection it is strongly recommended that this LCDmonitor is supplied via a RCCB. Safety unit.WARNING: To prevent injury LCD monitor must be securelyattached to the wall in accordance with the manufacturers installa-tion instructions .This monitor is tested to IP56 (Category 2) standard rating andmay be positioned in an outdoor environment exposed to rain.This monitor is not protected against temporary or continuousimmersion in liquid.Do not use immediately after moving the LCD monitor from a lowtemperature to a high temperature environment, as this causescondensation, which may result in fire, electric shock, or otherhazards. Before cleaning, unplug the monitor from the wallsocket.Do not mount near an open flame source. Open flames mustnever be used near this LCD monitor.This LCD monitor should not be built in or enclosed in any way,heat build up will reduce the life of the monitor.This LCD monitor should have a minimum distance of 5cm awayfrom the wall and the monitor should have 10cm distance aroundthe top and sidesDo not apply liquid cleaners or aerosol cleaners directly onto theLCD monitor. Use a damp cloth for cleaning.Always mount using recommended and substantial fixtures andfittings.The rear finned section around the cabinet functions as a heatsink, removing heat away from the monitor. The external surfaceof the cabinet (finned area) must not be covered or the airflowrestricted in anyway by enclosing the LCD monitorThe operating temperature range of this monitor is guaranteed0°c ~ 40°c. It is not recommended to install the screen in direct sun-light without adequate shading, as this will cause the temperature ofthe panel to rise above the maximum specified.Doing so may cause a black shadow to appear on the screen, whichwill disappear when the screen temperature returns to within thespecification. This “of course” does not produce any harmful effect onthe lifetime of the panel.InstallationCAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, butimproper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this receiver observethe following basic rules for its installation, use and servicing.UseImportant recycling information.Your SANYO product is designed and manufac-tured with high quality materials and componentswhich can be recycled and reused.This symbol means that electrical and electronicequipment, at their end-of-life, should be dis-posed of separately.In the European Union there are separate collec-tion systems for used electrical and electronicproducts.Please help us to conserve the environment welive in!Note: This symbol mark and recycle system are applied only to EUcountries are not applied to other countries of the world.GBImportant:THIS PRODUCT MUST BE EARTHEDThis equipment is fitted with an approved in-line waterproof mainscoupler and an approved non rewireable UK mains plug. Tochange a fuse in this type of plug proceed as follows:1. Remove the fuse cover and fuse.2. Fit a new fuse which should be a BS1362 5 Amp A.S.T.A. orBSI approved type.3. Ensure that the fuse cover is correctly refitted.If the fuse cover is lost or damaged the plug must NOT be usedbut replaced with a serviceable plug.If the fitted plug is not suitable for your socket outlets, it should becut off and an appropriate plug fitted in its place. If the mains plugcontains a fuse, this should have a rating of 5 Amp, ensure thefuse cover is correctly fitted. If a plug without a fuse is used, thefuse at the distribution board should not be greater than 5 Amp.Note: The severed plug must be destroyed to avoid a possibleshock hazard should it be inserted into a 5 Amp socket elsewhere.The wires in this mains lead are coloured in accordance with thefollowing code:Blue -------> NeutralBrown ----> LiveGreen and Yellow ----> Earth1. The Blue wire must be connected to the terminal which ismarked with the letter “N” or coloured BLACK.2. The Brown wire must be connected to the terminal with theletter “L” or coloured RED.3. The Green and Yellow wire must be connected to the terminalwhich is marked with the letter “E” or coloured GREEN orGREEN and YELLOW.Before replacing the plug cover, make certain that the cord grip isclamped over the sheath of the lead - not simply over the wires.Do not attempt to bypass the safety purpose of the groundingtype plug.THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESSTHE MAINS LEAD IS UNPLUGGED.THE INSTALLER MUST MAKE SURE THE WATERPROOF IN-LINE COUPLER IS EASILY ACCESSIBLE.