Sanyo DP26671 Owner's Manual

Also see for DP26671: Service manual Service manual

17 ENGLISHStarting setupThe Auto Setup menu appears the first time youturn on the TV, and assists you to specify theAir/Cable setting, and program your channelsautomatically.IMPORTANT: Make sure that the antenna or cableTV system connection is made!1 To turn on the TV, press POWER (POWERindicator on the front of the unit changes green.It may take approx. 10 seconds for a picture toappear on screen.). The Auto Setup functionbegins.Auto Setup:Adjust:SelectAutomatic Search StartThis unit has been preset to STORE brightnessThis setting does not qualify under ENERGYSTAR. To reduce brightness and energyconsumption, change setting to ‘HOME’. Thissetting does qualify underENERGY STAR.TV Location StoreSignal Type Cable2 Press ▲ or ▼ to select “TV Location”, then press◀ or ▶ to select “Home” or “Store”. This productqualifies for ENERGY STAR In Home modedefault setting.NOTE:This unit has been preset to STORE brightness.This setting does not qualify under ENERGYSTAR. To reduce brightness and energyconsumption, change setting to ‘HOME’. Thissetting does qualify under ENERGY STAR.The device may not conform to the ENERGYSTAR standard after Reset is performed or theBacklight is adjusted.••3 Press ▲ or ▼ to select “Signal Type”, then press◀ or ▶ to select “Cable” or “Air”.4 Press ▲ or ▼ to select “Automatic Search”, thenpress ▶ or ENTER.5 Now the “Auto Setup” starts. After the Auto Setupis completed, the TV channel appears on thescreen.• Depending on the reception condition, it maytake from 15 minutes to 30 minutes to completememorizing digital cable channels. Please be patient.NOTE:If you press EXIT in the process of “Auto Setup”,the Auto Setup stops and changes to the normalscreen.When you make a menu selection, your changesoccur immediately. You do not have to press EXIT tosee your changes.TV operation1 To turn on the TV, press POWER.(POWER indicator on the front of the unit changesgreen. It may take approx. 10 seconds for a pictureto appear on screen.)2 Adjust the volume level by pressing VOL + or – .The volume level will be indicated on the screen bygreen bars. As the volume level increases, so dothe number of bars. If the volume decreases, thenumber of green bars also decreases.••3 Set the Signal Type option to the appropriateposition (see “Air/Cable selection” on page 20).4 Press the Direct Channel Selection (0-9, –)buttons to select the channel.(If you press only channel number, channel selectionwill be delayed for a few seconds.)TO SELECT ANALOG CHANNELS1-9: Press 1-9 as needed. Example, to selectchannel 2, press 2, then press ENTER.10-99: Press the 2 digits in order. Example, toselect channel 12, press 1, 2, then pressENTER.100-135: Press the 3 digits in order. Example, toselect channel 120, press 1, 2, 0, thenpress ENTER.TO SELECT DIGITAL CHANNELSPress the first 1-3 digits, then press the – button,followed by the remaining number.Example, to select channel 15-1, press 1, 5, –, 1,then press ENTER.If a channel is selected with only audio content,“Audio only” will be displayed on the screen.If a channel is selected with a weak digital signal,“Digital channel signal strength is low” will bedisplayed on the screen.The same program may be available on eitheran analog channel or a digital channel. You maychoose to watch either format.If a channel is selected to which you have notsubscribed, “Digital channel is encrypted” will bedisplayed on the screen.•••VHF/UHF/CABLE CHANNELSAir CableVHF2-13VHF2-13UHF14-69STD/HRC/IRC14-36 (A) (W)37-59 (AA) (WW)60-85 (AAA) (ZZZ)86-94 (86) (94)95-99 (A-5) (A-1)100-135 (100) (135)01 (4A)NOTE:If a channel with no broadcast is selected, thesound will automatically be muted.It may take a few seconds for a digital channelpicture to appear on screen after being selected.To select the video input sourceTo view a signal from another device connected to yourLCD TV, such as a VCR player, press INPUT SELECT,then press ▲ or ▼ or corresponding Number buttons (0-7), then press ENTER. You can select TV, Video1, Video2,Component, HDMI1, HDMI2, PC or DVD depending onwhich input jacks you used to connect your devices.Input Select0.TV1.Video12.Video2[0-7]:Select3.Component4.HDMI15.HDMI26.PC7.DVDCH /Press and release CH / . The channelautomatically stops at the next channel set intomemory.For proper operation, before selecting channels, theyshould be set into the memory. See “Memorizingchannels” on page 20.••56Q0221A_eng.indd 1756Q0221A_eng.indd 17 1/8/11 5:31:55 PM1/8/11 5:31:55 PM