Sanyo DSR-3000 Instruction Manual
Also see for DSR-3000: Instruction manualService manual
                                                                                                                                                                                                                                            | |
Contents
| 
NETWORK SET SETTINGNETWORK SET setting1 Press the MENU button twice to display the MAIN MENU 2screen.The cursor moves to DISPLAY/VIDEO LOSS SET.2 Use the jog dial to move the cursor to the NETWORK SETsetting, and then turn the shuttle dial clockwise.The NETWORK SET sub-menu appears, and the cursor movesto LAN CARD.3 Turn the shuttle dial clockwise.“LAN1” flashes.Select LAN1 or LAN2 to suit the type of card being used.• LAN1: COREGA FEther PCC-TXD “CG-FEPCCTXD” type(10/100 BASE-T) or COREGA FEther II PCC-TXD“CG-FE2PCCTXD” type (10/100 BASE-T)• LAN2: COREGA Ether PCC-TD “CG-EPCCTD” type(10 BASE-T) or COREGA Ether II PCC-TD“CG-E2PCCTD” type (10 BASE-T) or COREGA Ether IIPCC-T (10 BASE-T) or D-Link DE-660Note: Correct operation cannot be guaranteed if a LAN card otherthan the one recommended above is used.4 Use the jog dial to select the LAN card (example: “ LAN1” ),and then turn the shuttle dial clockwise.The cursor moves to NETWORK CONTROL.5 Turn the shuttle dial clockwise and use the jog dial to selectNETWORK CONTROL (example: “ ON” ), and then turn theshuttle dial clockwise to set (DISPLAY: ON).The cursor moves to IP ADDRESS.• NETWORK CONTROL: ON (DISPLAY: ON) When DISPLAYis set to ON, the characters “NETWORK CONTROL” aredisplayed on the digital video recorder’s monitor output all thetime during a network connection. In addition, when imagesare being played back from the network, the digital videorecorder’s monitor output also shows the playback images.The digital video recorder cannot be operated during a networkconnection. However, you can disconnect from the network bypressing the EXIT/OSD button for 3 seconds.• NETWORK CONTROL: ON (DISPLAY: OFF) When DISPLAYis set to OFF, the characters “NETWORK CONTROL” are notdisplayed on the digital video recorder’s monitor output duringa network connection. In addition, when images are beingplayed back from the network, the digital video recorder’smonitor output shows live images. The PLAY/STOP indicatoron the digital video recorder does not illuminate duringplayback. (Recording is possible.) The digital video recordercannot be operated during a network connection. However,you can disconnect from the network by pressing theEXIT/OSD button for 3 seconds.• OFF: Network operations are disabled.Note:• Control through the network is not possible unless NETWORKCONTROL is ON.When you are connected to a network, it should be switched OFF ifcontrol from the network is not required.• If DIGITAL SERIES RECORDING in the RECORDINGCONDITIONS SET menu is set to “ON”, NETWORK CONTROLcannot be set to “ON”.• The main unit cannot be operated while network operations are inprogress. However, the digital video recorder can be disconnectedfrom the network by pressing the EXIT/OSD button forapproximately 3 seconds.6 Turn the shuttle dial clockwise and use the jog dial andshuttle dial to display the IP ADDRESS (example:“ 192.168.0.1” ), and then turn the shuttle dial clockwise.With the final shuttle dial movement, the cursor moves toSUBNET MASK.7 Turn the shuttle dial clockwise and use the jog dial andshuttle dial to display the SUBNET MASK (example:“ 255.255.255.0” ), and then turn the shuttle dial clockwise.With the final shuttle dial movement, the cursor moves toGATEWAY.MENU |
Related manuals for Sanyo DSR-3000
Sanyo DSR-3000 Instruction Manual
Sanyo DSR - 300 Instruction Manual
Sanyo DSR-3000P Instruction Manual
Sanyo DSR-3016 Instruction Manual
Sanyo DSR-3016P Instruction Manual
Sanyo DSR-M800 Instruction Manual
Sanyo DSR-HB8000 Instruction Manual
Sanyo DSR-3506 Instruction Manual
Sanyo DSR-3716 Instruction Manual
Sanyo DSR-3709 Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine